Scope Of Deliverables; Intended Use; Before Commissioning - Hurricane HBFI 75 Instrucciones De Manejo

14b Cutting blade protective cover
15. Carry belt
16. Cutting blade
17. Wrench for spool change
19. 3 x bolts for protective cover
20. Securing split pin
25. Fastening ring
26. Driving plate
27. Nut
28. Oil/petrol mixing bottle
29. Spark plug wrench
30. Allen key
31. Locking pin

Scope of deliverables

• Open the packaging and take the device carefully out
of the packaging.
• Remove the packaging material and the packa-
ging/transportation locks (if present) (fig. 14)
• Check whether the delivery is complete.
• Check the device and the accessories for transportation
damage.
• Keep the packaging safely until the guarantee period
has expired, if possible.
ATTENTION
The device and the packing are not children's toys!
Children must not be permitted to play with plastic
bags, film and small parts. There is a risk of them
being swallowed and danger of suffocation!

Intended use

The device is intended for cutting lawns and grass areas.
The observance of the manufacturer's operating instruc-
tions included is a prerequisite for the proper use of the
device. Any other use that is not expressly permitted in
these instructions can lead to the device being damaged
and a serious risk for the operator. Observe the restricti-
ons in the safety instructions. Please note that our device
has not been designed with the intention of it being used
for commercial, trade or industrial applications. We ac-
cept no liability if the device is used in commercial, trade
or industrial operations or corresponding activities.
Attention! Due to bodily endangerment of the operator
the following work must not be undertaken with the motor
scythe: Clearing pathways and as a chipper for shredding
tree and hedge cuttings. Furthermore, the motor scythe
must not be used for levelling bumps in the ground such
as mole hills for example. For safety reasons the motor
scythe must not be used as a drive unit for other tools or
tool sets of any type. The machine must only be used for
its intended purpose. Any other use shall be considered
improper use. The user/operator, and not the manufac-
turer, is responsible for any damage or injuries arising
from this.

Before commissioning

1 Assembly
1.1 Fitting the guide handle
Fit the guide handle as shown in fig. 3a-3c. Only tighten
the screws completely once you have set the optimum
working position with the help of the carry strap. The
guide handle should be arranged as shown in fig. 1. Re-
moval is carried out in reverse order.
1.2 Guide shaft assembly (fig. 4a – 4b)
Loosen the handle screw (A) on the coupling sleeve (B),
pull the knob (D), feed the drive axle (C) in and let it latch
into place. In doing so ensure that the drive shafts in-
side the guide shaft mesh together properly (turn the reel
head a little if necessary). Now tighten the handle screw
(A) as shown in fig. 4b. After being assembled for the first
time the handle screw need only be loosened a little and
the lever actuated in order to dismantle the guide shaft.
1.3 Fitting the blade guard
Attention: When working with the cutting blade the cutting
blade guard must be installed. The cutting blade guard is
fitted as shown in figs. 5a-5b.
1.4 Fitting/replacing the cutting blade
The fitting of the cutting blade is shown in figs. 6a-6f. Re-
moval is carried out in reverse order.
• Fit drive plate (26) to the splined shaft (fig. 6b)
• Lock cutting blade (16) onto the cover ring (fig. 6c)
• Place fastening ring (25) over the thread (fig. 6d)
• Find the hole in the drive plate, align with the notch un-
derneath and lock with the locking pin supplied (31) to
enable the nut (27) now to be tightened
Attention: Left-hand thread (fig. 6e)
• Slide the safety split pin (20) through the hole in the
drive shaft and bend the legs around the shaft as
shown in fig. 6f.
1.5 Fitting the protective cover for the trimming line
Attention: When working with the trimming line the
protective cover for the trimming line must also be in-
stalled.
• Place the protective cover for the trimming line on the
blade guard (fig. 7a).
• Fasten the protective cover for the trimming line in
place with the screws for the protective cover (fig. 7b).
1.6 Fitting/replacing the cutting line spool
The fitting of the cutting line spool is shown in fig. 7c.
Removal is carried out in reverse order.
Find the hole in the drive plate, align with the notch un-
derneath and lock with the locking pin supplied (31) and
screw the cutting line spool onto the thread.
Attention: Left-hand thread (fig. 7c)
2 Setting the cutting height
ATTENTION! - Always use the shoulder strap.
Attach the strap to the device immediately after
starting it whole the engine is idling. Always
switch the engine off first, when you detach the
strap.
GB-5