Nexia BE369 Manual De Instalación

P516-085
1
Important Information
• Lock comes preset with a default Programming Code.
• Lock comes preset with two default User Codes
Default Programming Code
Código de programación predeterminado
Code du défaut programmation
Place Label Here
Default User Codes
Poner la etiqueta aquí
Códigos de usuario predeterminado
Placer l'autocollant ici
Codes du défaut utilisateur
2
Install deadbolt and strike.
2a. Check dimensions.
2b. Check backset.
If door dimensions do not match, go to This lock will fi t either a 2³⁄₈" backset or a 2³⁄₄" backset. The bolt is preset to fi t a 2³⁄₈" backset. If
your backset is not 2³⁄₈", you need to adjust your bolt by rotating it counterclockwise.
www.nexiahome.com for drilling instructions.
2³⁄₈" (60 mm)
OR
2³⁄₄" (70 mm)
5¹⁄₂"
(140 mm)
2¹⁄₈" (53 mm)
Hole
3
Align tailpiece of exterior keypad and interior baseplate.
3a. Check the cam on the interior baseplate.
Locate the cam on the baseplate. This cam has a small arrow on it that
should point to the arrow that is printed on the casing above the cam, like
picture "a" below. If the cam is oriented sideways, like the picture "b",
rotate the cam until the arrows match.
a b
Correct Incorrect
4
Secure interior baseplate and install batteries.
4a. Secure interior baseplate.
Use the two screws shown to secure the baseplate to the door.
5
Install interior cover.
5a. Install cover.
Place the cover against the door and secure using the two screws. You may
need to rotate the thumbturn to the proper position, shown below.
Tuck wires into open space on baseplate. Be careful not to pinch any wires
between cover and baseplate.
Actual Size
Thumbturn
Actual Size
7
Test lock. TEST WITH DOOR OPEN!
7a. Test locking function.
1. Press
2. Rotate thumbturn towards door edge until bolt extends.
Yes. Lock is installed correctly.
HOME KEYPAD LOCK
INSTALLATION INSTRUCTIONS
MODEL BE369
Need Help?
(877) 288-7707
(U.S.A./Canada)
nexiahome.com
2³⁄₈" (60 mm) 2³⁄₄" (70 mm)

OR
3b. Install exterior keypad.
Bar should slide smoothly through hole in latch. If not, check door dimensions. Feed the cable over the
top of the bolt assembly then slide the tailpiece through the correct hole as shown below.
4b. Connect cable.
Snap the connectors together. Tuck them into the open space in the
baseplate. Make sure no wires will be pinched when the cover is installed.
Actual Size (2)
6
Install the strike.
6a. Prepare the frame for the strike.
Mark the 4 hole locations. Drill them as shown.
If the strike cut-out has not been prepared in the frame, see the specifi cations on the right.

Did bolt extend?
No. Lock is not installed correctly.
Remove lock and reinstall. Pay close
attention to cam position in step 3a.
Correct Incorrect
Tools Needed
• Phillips screwdriver
• Tape Measure
• Pencil
Optional
Keypad
• Flathead Screwdriver
• Wood Block
Key
• Hammer
Do not use a power
drill for installation
2c. If necessary, change bolt faceplate
Check edge of door to determine the type of faceplate
required.
2 ³⁄₄
No change
OR
necessary.
Exterior
Tailpiece Tailpiece

(38 mm)
¹⁄₈" (3 mm)
7b. Test unlocking function.
1. Find User Code A on the yellow sticker.
2. Enter User Code A (four digits) into the keypad.
3. Rotate thumbturn away from door edge until bolt retracts.
Yes. Lock is installed correctly.
Contents
Baseplate
Screws (2)
Interior
Baseplate
Latch/Strike
Screws (4)
Strike
Reinforcement
Screws (2)
2d. Install bolt.
The word "TOP" should be facing upward.
3c. Install the interior baseplate.
Feed the cable through the hole as shown below. DO NOT connect the cable at this
time. Then slide the baseplate onto the tailpiece and press against the door. The
baseplate should stay in place.
IMPORTANT
Cable must slide
Interior
over latch.
4c. Install batteries.
1.
Unscrew battery holder.
2.
Slide out battery holder and install batteries.
3.
Attach 9 volt battery to battery connector.
4.
Place 9 volt battery in compartment.
6b. Install the strike.
Strike cut-out specifications
(not to scale)
1"
(25 mm)
1" (25
mm)
1¹⁄₂" 2³⁄₄"
(70 mm)
1¹⁄₈"
(29 mm)
Did bolt retract?
No. Lock is not installed correctly.
Remove lock and reinstall. Pay close
attention to cam position in step 3a.
Correct Incorrect
Top Cover
Screw
Cover
Bottom Cover
Screw
Alternate
Faceplate
AA Batteries (3)
not included
Strike
9 Volt Battery
Reinforcement
not included
Plate
Actual Size (2)
OR
2 2
1 1
4 4
3 3
Actual Size (2)
Actual Size (2)
7c. Set up your online account.
1.
Browse to www.mynexia.com.
2.
Look for "Ready to setup a Nexia™ Home Intelli-
gence system? Get started here!" and click the link.
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifi cations to this equipment not expressly approved by
Schlage could void the user's authority to operate the equipment.
FCC ID: P2GBE369 IC: 7654A-BE369
© 2013 Ingersoll Rand
Printed in U.S.A.
P516-085 01/13 c