Gas Burners - ROSIERES YWCR8308 Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

GAS BURNERS

Each burner is contolled by a tap with progressive settings allowing:
* a wider choice of settings from the maximum position to the
lowest and most precise one,
* easier flame regulation according to the pan diameter,
* no risk of cutting off the flame or switching off when the
flame is turned down quickly.
IGNITION
RECOMMENDATIONS : when the burners are not in service,
the general gas
supply tap should always be turned off.
• Turn on the gas tap,
• A symbol next to each control knob indicates which burner is lit.
• Turn and press in the relevant burner control knob to the "+"
(
) symbol, keeping it pressed in until the flame ignites. On
models fitted with electronic ignition the flame is ignited by an
electric spark. This is operated by the button or by pressing the
knob (for models with ignition under the knob).
For models not fitted with electronic ignition, or if there is no
electric power, light the flame with a match.
NB: for models fitted with the SAFETY thermocouple, keep
the knob pressed in for a few seconds in order to activate
the safety system. If the knob is released straightaway
there is not time for the safety system to be activated and
the flame goes out. If this happens, repeat the ignition
procedure from the beginning waiting longer after the
flame is lit.
The rapid thermocouple safety device automatically cuts
off the gas supply if the flame is accidentally extinguished.
If there are particular local gas supply conditions which make
ignition difficult, you are advised to repeat the ignition procedure,
turning the knob to "minimum" ( ).
• Set the flame according to your cooking requirements. Intermediate
positions are available between the "+" ( ) and "-" ( ) settings
on the control knob.
• To turn the flame out, turn the control knob back to stop position.
• If the burner is accidentally extinguished, turn the knob to "0",
wait one minute and then try to ignite again.
PANS
For a proper use of the burners, choose pans which match the
dimensions given below :
* Double ring Ø 18 cm and more
* Very fast Ø 18 cm and more
* Fast Ø from 16 to 18 cm
* Semi-fast Ø 12 cm
• Pans with curved, ridged or warped bottoms are not
recommended.
• Aluminium pans may leave marks on the enamelled
pan support. These marks can easily be removed with
a damp cloth and a light abrasive product.
SOME TIPS ....
• Avoid boiling food too intensely. Food is not cooked any more
quickly this way. In fact,
it is subjected to severe agitation, which may cause the food to
lose some of its flavour.
• To save gas, make sure that the flames do not overlap the bottom
of the pan.
• Do not use the gas burner with an empty pan.
USE
THE ELECTRICAL HOT-PLATE
THE ELECTRIC HOTPLATE:
the power is controlled by the position of the knob
(see table below).
The electric hotplates with a red dot in the middle
are rapid ones with automatic protection; there is an internal
thermostat in these hotplates which automatically reduces the
power when an abnormal temperature is detected (for example,
when operating empty).
THE HIGHLIGHT HOTPLATE: used with glass/ceramic products;
it has a metallic laminate which spreads the heat uniformly over
the whole area. It heats up in three seconds and allows even and
delicate cooking as well as high temperature cooking; power is
regulated by the position of the knob (see table below).
BEFORE USING THE ELECTRICAL HOT PLATE :
• Before using the electric hot plate for the first time, let it heat up
for a few minutes, without a pan, at maximum temperature to allow
the protective coating to harden.
HOW TO USE :
• For best results, it is advisable to start on the maximum heat
and then turn back to an intermediate temperature taking into
account the type and volume of the food.
• An indicator light comes on to show that the hot plate is operating.
• To switch off, turn the knob back to point "0".
DIFFERENT TEMPERATURE SETTINGS :
Below are a few examples which are given as guidelines. When
you become more familiar with the appliance, you will be able to
choose settings to suit your own personal tastes and requirements.
ON VETROCERAMIC HILIGHT ZONE
The residual heat indicator lights up when the hilight zone
temperature is 60° C and above. It will stay on, even if the zone
is switched off, until the surface has cooled down. It will switch off
when the temperature of the surface falls below 60° C.
Positions
1
1-2
Very Low
To keep a dish hot, melt butter and chocolate...
Slow cooking, sauces, stews, rice pudding
2
3-4
Low
poached eggs...
3
5-6
Moderate
Beans, frozen foods, fruit, boiling water...
Steamed apples, fresh vegetables, pasta,
4
7-8
Medium
crepes, fish...
5
9-10
High
More intense cooking, omelettes, steaks...
6
11-12
Very High
Steaks, chops, frying...
SOME TIPS ....
To get the best results from your appliance it is important to
observe the following :
• Use thick, flat-based cooking vessel :
a completely flat base prevents overheating to certain parts
which causes food to stick. Thick metal allows for good heat
distribution.
• Make sure that the base of the pan is dry :
this will prevent sticking to the hot plate caused by moisture.
• Use pans with a diameter large enough to completely cover
the hot plate,
otherwise energy will be wasted and any spillages will cause the
hot plate to become stained and will become difficult to maintain
(rust, etc.).
• Never leave a hot plate switched on without a pan on it :
it can be damaged, which would reduce its efficiency.
• When cooking with fat or oil, never leave the hob unattented,
very hot fats and oils can quickly catch fire.
• When the hot plate is hot, avoid any contact with materials made
of plastic or aluminium foil.
Caution :
the heating surfaces clearly get hot while operating, so make
sure that small children are kept well away from the hob.
11 GB
Some Tips

Publicidad

Tabla de contenido
loading

Tabla de contenido