Operation; Recording; Storage Locations M1 - M6; Storage Locations Voice01 - Voice20 - Monacor PA-1120DMT Instrucciones Instalación Y Funcionamiento

6 Operation

When the amplifier or the basic unit is switched
on, the display (4) of the insertion module will
show the weekday and the time . The unit will
always automatically return to this indication
after 30 seconds when, for example, no button
is pressed in a menu . To cancel a menu setting at
any time, press the button MENU (10) .

6.1 Recording

To record a message, connect a microphone or a
mono audio source with line level to the 2-pole
jack (7) and set the switch (9) for the input sensi-
tivity to the corresponding position: MIC (micro-
phone) or LINE (line level) .
During recording, the input signal will be
replayed via the amplifier . However, it is also
possible to use headphones for monitoring the
input signal: Connect the headphones (minimum
impedance: 64 Ω) to the jack PHONES (3) [mono,
only the left side for stereo headphones); the out-
put (26) to the amplifier will be muted .
Please refer to chapter 6 .6 for information on
how to use externally created recordings .
6.1.1 Storage locations M1 – M6
To record a message on one of the storage loca-
tions "M1" to "M6":
1) Press the button (15) of the storage location
desired . The display will show, for example:
M3
PlayMode
If pressing this button starts the replay of the
stored message, press the button REPEAT/ STOP
(13) to stop the replay .
2) Press the button PLAY/ REC (1) . The display will
switch to the recording mode:
M3
Rec Mode
3) Press the button START/ STOP (14) . First,
will appear on the lower line of the
Erase
display and the storage location will be cleared .
Recording will start when the first line of
the display shows
number . On the lower line, a bar graph will
appear, indicating the level of the input signal .
4) Use the control REC LEVEL (2) to adjust the
level of the signal to be recorded in such a way
18
, following the storage
REC
that not all segments of the bar graph will be
shown for peaks .
5) To stop the recording, press the button
START/ STOP .
6.1.2 Storage locations Voice01 – Voice20
To record a message on one of the storage loca-
tions "Voice01" to "Voice20":
1) Press the button MENU (10) . The display will
show:
Mode Set
Time
2) Press the button UP (12) or DN (11) repeatedly
until appears on the lower line of the
Voice
display .
3) Press the button ENTER (6) . The display will
now show:
Choose
Play
4) Use the button UP or DN to select the option
on the lower line .
Rec
5) Press the button ENTER . The display will now
show:
Record
Voice:01
6) Use the button UP or DN to select the storage
location desired for the recording (
7) Press the button START/ STOP (14) or ENTER .
First, will appear on the lower line of
Erase
the display and the storage location will be
cleared .
Recording will start when
pears . A bar graph will appear instead, indi-
cating the level of the input signal .
8) Use the control REC LEVEL (2) to adjust the
level of the signal to be recorded in such a way
that not all segments of the bar graph will be
shown for peaks .
9) To stop the recording, press the button
START/ STOP or ENTER .
Now, will appear on the display; the
PlayBack
button START/ STOP can be pressed to immedi-
ately replay the message stored . To select a differ-
ent storage location for replay, use the button UP
or DN ( ☞ chapter 6 .2 .3) .
To exit the menu, press the button MENU .
to ) .
01 20
disap-
Erase