Service And Storage - Evans G85MG1400KAE Manual De Propietario

EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
5
Close the fuel shut off valve if the engine is to be put in
storage or transported.
6
If cover is used, do not install it until the generator is
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
cool.
INITIAL START PROCEDURE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
Controlled initial start helps insurance of proper engine
and generator operation. Follow engine start procedure
outlined in engine manual.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
Do not apply a heavy electrical load during
start period (the first two to three hours of
operation).
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
MAINTENANCE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
ATTENTION: Disconnect all loads plugged to the panel,
and the cable of the spark plug (if engine is of electrical
start), before any inspection or maintenance.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
1
Before each use, review the general conditions of the
generator. Review that all pieces are complete. Review
if there are damaged cables or some other conditions
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
that can affect that the generator operates on a safe
way. If an abnormal noise is listened or some abnormal
vibration occurs, turn off the generator immediately. Be
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
sure to fix the problem before giving the generator more
use. Do not use the equipment damaged.
2
Periodically inspect all the screws and bolts to check
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
they are in place and tight.
3 Keep the generator in a clean and dry place.
For the best maintenance of the engine and any other
4
problem related, read the engine owner's manual.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
5
After the engine has become cool, remove the excessive
gasoline and store it in a container, safe and approved
for that purpose.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
6
After the first 20 hours of use of the generator drain and
replace the oil of the engine. After that, the oil must be
changed every 100 working hours
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
HEAT SHIELD:
Inspect to ensure that all heat shields and heat deflectors
are intact and in place. Removal of these parts could
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
cause serious damage to the unit.
ENGINE: Carburetor Icing
During the winter months, rare atmospheric conditions
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
could cause an icing condition in the carburetor. If it
happens, the engine may run rough, loose power, and
may stall. Call Product Service for more information.
NOTE: Refer to the engine manufacturer's manual for
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
service and maintenance of the engine.
QUICK STARTING TIPS FOR UNITS THAT
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
HAVE BEEN SAT FOR A WHILE
If your unit has not been used for a long period of time
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS. and it is hard to start it, try to do some of the following
easy steps before calling the customers hotline.
1
Check the oil level.
2
Replace the old fuel.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
8
CAUTION
3
Change the spark plug.
4
Check the fuel lines. Make sure the fuel valve is open.
5
Check all generator parts for integrity
6
Clean the carburetor.

SERVICE AND STORAGE

INFREQUENT SERVICE
If the unit is used infrequently, difficult starting may result,
to eliminate hard starting, run the generator at least 30
minutes every 15 days. Also, if the unit will not be used
for some time, it is a good idea to drain the fuel from the
carburetor and gas tank.
LONG TERM STORAGE
When the generator has been storaged for long periods
of time (like more than one month) follow the instructions
below to start the generator again:
1
Replenish engine oil to upper level.
2
Drain gasoline from fuel tank line and carburetor.
3
Pour about one teaspoon of engine oil through the spark
plug hole, pull the recoil starter several times and replace
the plug. Then pull the starter until you feel piston is on
its compression stroke and leave it in that position. This
closes both the intake and exhaust valves to prevent the
inside of cylinder from rusting.
4
Cover the unit and store in a clean, dry place that is well
ventilated away from open flame or sparks.
NOTE: We recommend always using a fuel stabilizer.
A fuel stabilizer will minimize the formation of fuel gum
deposits during storage. The fuel stabilizer can be added
to the gasoline in the fuel tank, or into the gasoline in a
storage container.
READ THE FOLLOWING CAREFULLY
THE MANUFACTURER HAS PROVIDED IN THIS
MANUAL THE PRODUCT EXPLODED DRAWING
INCLUDING THE LIST OF MAIN COMPONENTS OF
THE PRODUCT AS A REFERENCE TO THE END
USER ONLY. IT DOES NOT IMPLY THAT BUYER
AND/OR END USER IS AUTHORIZED TO USE THIS
INFORMATION AS A BASIS TO PERFORM BY
ITSELF ANY PARTS REPLACEMENT OR REPAIRS
TO THE PRODUCT. ON PRINCIPLE, BUYER
AND/OR END USER IS CONSIDERED BY THE
MANUFACTURER UNQUALIFIED TO PERFORM BY
ITSELF ANY REPAIRS OR PARTS REPLACEMENT
TO THE PRODUCT. ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN
BY AN AUTHORIZED SERVICE CENTER OR A
PROPERLY QUALIFIED TECHNICIAN. BUYER AND/
OR END USER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS OR
PARTS REPLACEMENT MADE BY ITSELF TO THE
ORIGINAL PRODUCT.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE