Connections & System Control - Gemini CTRL-ONE Manual De Instrucciones

Back Panel Controls
1) POWER SOURCE SELECTOR switch: This switch alternates
the unit between the OFF position and ON position. When set to
OFF, the unit is powered off. To turn the unit ON, select one of two
possible power sources corresponding to which you intend to use
to power the device, namely ADAPTOR for the DC power adaptor,
and USB for a USB connection with a computing device.
1a) POWER LED: When connected to a power source and turned
on properly, the POWER LED will illuminate to indicate that the
unit is on.
2) 5V DC INPUT: To power your unit using an adaptor, connect
a 5V 1000 mA DC adaptor to the device and a power source,
then select ADAPTOR on the POWER SOURCE SELECTOR (1)
switch.
3) USB INPUT: To power your unit using the included USB cable,
connect the adapter to the device and a USB slot on a computing
device powerful enough to supply the unit, then select USB on the
POWER SOURCE SELECTOR (1) switch.
Top Controls
*Note: Some of the following functions appear on the unit twice, how-
ever they are explained only once because they operate in the same
manner on each channel respectively.
4) MASTER VOLUME rotary knoob: The MASTER VOLUME ro-
tary knob adjusts the overall volume of the units output.
5) CHANNEL ROTARY GAIN: The CHANNEL ROTARY GAIN al-
lows you to boost the signal of each individual channel depending
on how low or high its input level is.
6) CHANNEL VOLUME FADER: The CHANNEL VOLUME FAD-
ER alternates the volume of the corresponding channel between
the maximum allowable level and 0.
7) VU METER: The CTRL ONE has a stereo VU METER that al-
lows you to monitor the decibel levels of the LEFT and RIGHT
MASTER output.
8) CROSS FADER: The CROSS FADER allows you to mix evenly
from one channel to another.
9) 3 BAND EQUALIZER: The 3 BAND EQUALIZER adjusts the
tone of each channel by giving you a choice of 3 frequencies
(BANDS) to adjust, from LOW, MIDRANGE (MID) and HIGH. You
can use the adjustment knobs to higher or lower the 3 separate
frequencies till the sound of the music program is appropriate for
your listening environment.
10) TRACK/ FOLDER SEARCH: The TRACK/ FOLDER SEARCH
allows you to navigate through folders or tracks similarly. Turn
the knob to the right to advance the selection, or turn the rotary to
the left to decrease the selection. Push the knob to engage the
selection.
Connections and System Control
8
Conexiones y Control de sistema • Connexions & Utilisation • Anschlüsse und Systemeinstellungen
Connections and System Controls • Conexiones y Controles Sistema
Connexions & Fonctions • Anschlüsse und Bedienelemente
10a) LOAD A/ LOAD B: When you have selected a file for play, it
is assigned to channel A or channel B by pressing the LOAD A or
LOAD B button.
11) FOLDER OUT: The FOLDER OUT button is used after you are
finished navigating through folders. When pressed ONCE it will
navigate one level BACK.
12) PLAY: Pressing the PLAY button engages the selected file.
13) PAUSE: Pressing the PAUSE button temporarily stops the file
from playing, and freezes it in its current location. Press the PLAY
(12) button to start the file.
14a) SEARCH: To search within a playing track, press the
SEARCH button, and turn the jogwheel clockwise to fast-forward
and counter-clockwise to rewind.
14b) SCRATCH: Pressing the SCRATCH button engages the unit
in scratch mode. The jogwheel is used to simulate the effect of
scratching a record.
15) CUE: Creating and storing CUE points is quick and easy. By
default, when there is no CUE Point set (or memorized), press-
ing the CUE button returns the unit to the beginning of the track
(0:00.00) and pauses it. To set a CUE point during playback at a
time of your choice, simply press PAUSE (13) and then use the
SEARCH (14a) function to make any adjustments by frame. When
the precise location is found, press CUE to store this point or press
any HOT CUE (15a) 1-3 button to store it.
While the unit is playing and after the cue point has been pro-
grammed, pressing CUE will cause the player to enter the PAUSE
mode (PLAY/PAUSE BUTTON blinks) at the programmed cue
point (the CUE LED is lit). Holding down the CUE button changes
the function to preview , and allows you to stutter start or play
from the programmed CUE POINT Releasing the CUE button will
return the player to the preset CUE point.
16) PITCH: Pushing and holding the PITCH button activates the
PITCH CONTROL SLIDE. You can then select which PITCH per-
cent you want by pressing the PITCH button and choosing 6%,
8%, 10%, 12%, 20%, 25%, 33%, 50%, and 100%.* Push and hold
the PITCH button again to deactivate this mode.
17) PITCH CONTROL SLIDE: Moving the PITCH CONTROL
SLIDE up or down will lower or raise the pitch percentage + or -
6%, 12%, 25%, 33%, 50%, and 100%.*
*Note: Only 6%, 12%, 25%, and 100% on the unit.
18) PITCH BEND: Pushing the PITCH BEND BUTTONS will au-
tomatically raise the pitch up to +16% or lower the pitch down to
-16% from the existing pitch setting. Releasing the buttons will re-
turn the pitch to the original pitch setting. You can use this function
to match the beat when mixing from one song to another.
19) BPM: Press and hold the BPM button to turn on the BPM read
out. Once on, you may TAP the button to the beat of the music.
CTRL-ONE - EN