Super Ego SEH000100 Instrucciones De Uso página 6

GB Operating Instructions E Instrucciones de uso
intended for the particular type of power tool, taking
into account the working conditions and the work to be
performed. Use of the power tool for operations different
from intended could lead to a hazardous situation.
Service
- Have you power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS
MACHINES
- Remove the battery from the machine during maintenance
and when the machine will not be used for a prolonged
period of time.
- Only use the prescribed type of battery (see technical
data).
SAFETY INSTRUCTIONS
BATTERY
- Read the general instructions and safety instructions
carefully before charging the battery.
- Only use the supplied charger to load the battery. Do not
charge batteries of another type with this charger. Mains
adaptors are only to be used together with te charger
socket and the accompanying battery.
- Only use charger in a dry environment at a temperature
between 10°C and 40°C.
- Do not use the charger when it has been damaged.
- Only have the charger and battery repaired by a qualified
engineer.
- Prevent the battery from short circuiting. Make sure
that the battery connections cannot touch any metallic
objects.
- Do not store the battery where the temperature may rise
above 50°C, e.g. in a car which has been parked in the
sun.
- Do not burn the battery.
- Never attempt to open the battery.
- Keep the battery away from children and pets.
OPERATION
Your rechargeable screwdriver is equipped with a circuit
protecting board, working light and led power level
indicator.
Charging the battery
- The battery must be charged before first use. Only after
several charger and discharge cycles the battery will
attain full capacity.
- Plug the charger into the socket on your screwdriver.
- Insert the charger into the appropriate 240V mains outlet.
FOR RECHARGEABLE
FOR CHARGER AND
The red indicator light will illuminate.
- Standard charging time is 3 to 5 hours, when the red led
light turns off, the battery is fully charged. Important! Please
note the battery must always be charged fully until red light
turns off.
- Battery discharge: When using your screwdriver, the
battery power will decrease gradually. The screwdriver
will stop working automatically when the battery power
reaches it's safety charge limit, when this occur, stop
using your screwdriver immediately and re-charge the
battery as described above.
Inserting and removing a screw bit
- Insert the screw bit into the bit holder, the bit holder is
magnetic to will not need to be tightened.
- In order to remove the screw bit pull if from the bit holder.
If necessary, use a pair of pliers.
Switching on and off
- To fasten a screw, press the upper on/off trigger switch.
- To loosen a screw, you press the lower on/off switch.
- To switch off the machine, release the upper or lower on/
off switch.
WARNING! Always wait until the motor has come to
a complete standstill before changing the direction of
rotation.
Light Switch
Your screwdriver is equipped with a LED light (at the front,
above the bit holder). You can switch it on by pushing the
switch on top of the machine to the front. To switch off the
light, slide the switch back to the rear of the screwdriver.
Led power indicator.
The 3 LED power level indicator (top rear of your machine)
gives you an indication of the remaining power level of the
battery. Push the test button of the power level indicator,
if all 3 green: green, yellow and red led light, it means
the battery is full. If only the yellow and red led light, the
battery still has some power though you should recharge it
soon. If only the red led lights, the battery is exhausted and
should be recharged right away.
Over current protection.
Your screwdriver is equipped with an over current
protection to protect the electrical motor and the Li-ion
battery. The battery will have a longer life time ad can resist
duty (charge/discharge) cycles.
If your screwdriver stops during operation, it means the
load was too heavy. (The current was too high and could
burn the motor). Wait a few seconds before continuing
operation.
6