Waketower Can Speakers Installation Instructions; Important Safety Information; Mounting The Speakers; Speaker Information - Fusion Waketower Can Instrucciones De Instalación

Waketower Can Speakers Installation
Instructions

Important Safety Information

Failure to follow these warnings and cautions could result in
personal injury, damage to the vehicle or vessel, or poor product
performance.
This device must be installed according to these instructions.
Disconnect the vehicle's or vessel's power supply before
beginning to install this product.
Continuous exposure to sound pressure levels over 100 dBA
may cause permanent hearing loss. The volume is typically too
loud if you cannot hear people speaking around you. Limit the
amount of time you listen at high volume. If you experience
ringing in your ears or muffled speech, stop listening and have
your hearing checked.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
It is strongly recommended that you have your audio system
installed by a professional installer to ensure optimum
performance.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation, go
to www.fusionentertainment.com
What's In the Box
• Two Waketower can speakers
Materials and Tools Needed
2
• 18 AWG (0.82 mm ) wire (speakers)
2
• 20 AWG (0.5 mm ) wire (LEDs)
• 3 A in-line fuses (LEDs)
• Speaker mounting bracket (sold separately)
1
• Drill and 12 mm ( / in.) drill bit
2
• Wire strippers
• Solder and heat-shrink tubing for wire connections
NOTE: For customized installations, additional tools and
materials may be needed.

Mounting the Speakers

You must purchase mounting brackets for the FUSION
Waketower Can speakers separately. Each type of mounting
bracket contains specific installation instructions.
1
If necessary, mark the locations on the waketower or the
deck where you plan to mount the speakers.
2
If necessary, drill a 12 mm (
the waketower or deck.
3
Route the speaker and LED power wires (not included) to the
mounting locations.
4
Using the installation instructions provided with the mounting
bracket, connect the bracket to the speakers and to the
waketower or the deck.
5
Connect the speaker wires
6
If necessary, connect the LED power wires
Wiring, page 2).
2
WARNING
CAUTION
NOTICE
for product support.
1
/ in.) cable pass-through hole in
2
(Speaker Wiring, page 2).
(Speaker LED
7
If speakers were installed at an angle, rotate the front of the
speaker and the endcap so the FUSION logo appears level
(Adjusting the Angle of the FUSION Logos, page
Speaker Wiring
When connecting the speakers to your stereo, observe these
considerations.
• Speaker wire is not included with the speakers. You should
use 18 AWG (0.82 mm
speakers to the stereo.
• You should make all wiring connections using solder and
heat-shrink tubing (not included).
• You can use this table to identify the polarity of the leads on
the speaker.
White
White with a black stripe
Speaker LED Wiring
You can control the color of the LEDs through the polarity of the
LED wires.
• Wire is not included with the speakers. You should use
20 AWG (0.5 mm
LEDs to power.
• You should connect the positive (+) power wire to a 12 Vdc
power source through an isolator switch or circuit breaker to
turn the speaker LEDs on and off.
NOTE: You can use the same isolator or circuit breaker
controlling the power supply to your stereo, which allows you
to turn the speaker LEDs and the stereo on and off at the
same time.
• You should make all wiring connections using solder and
heat-shrink tubing (not included).
• You can use this table to connect the LED wires from the
speaker to power according to the preferred LED color.
Blue LED
White LED
Adjusting the Angle of the FUSION Logos
You should secure the speaker to the waketower or the deck
before adjusting the angle of the FUSION logos.
If you installed the speaker at an angle, you can rotate the front
and the endcap so the FUSION logos appear level.
1 Remove the six #2 Phillips screws holding the front of the
speaker to the can.
2
Rotate the front of the speaker until the FUSION logo
appears level.
You can rotate the front of the speaker in 30-degree
®
increments.
3
Secure the front of the speaker to the can using the screws
you removed in step 1.
4
Rotate the endcap on the back of the can by hand until the
FUSION logo appears level.
5
Repeat this procedure for other speakers on the boat, as
needed.

Speaker Information

True-Marine
True-Marine products are subjected to rigorous environmental
testing under harsh marine conditions to surpass industry
guidelines for marine products.
Any product that bears the True-Marine stamp of assurance has
been designed for simplicity of use and combines advanced
marine technologies to deliver an industry leading entertainment
2
) speaker wire to connect the
2
) or thicker wire to connect the speaker
Black to negative (-)
Red to positive (+)
Black to positive (+)
Red to negative (-)
™ Products
2).
Positive (+)
Negative (-)
Installation Instructions