Proper Use; Technical Data - HERKULES H-DS 400 Manual De Instrucciones Original

3. Proper use

The belt and disk grinding/sander is designed for
grinding/sanding all types of timber commensura-
te with the machine's size.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
The machine is allowed to be operated only with
suitable grinding/sanding belts which comply with
the data specifi ed in this manual.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards.
It is also imperative to observe the accident pre-
vention regulations in force in your area.
The same applies for the general rules of health
and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Harmful emissions of wood dust when used
in closed rooms.
•
The rotating parts of the device cannot be
covered for functional reasons. Therefore you
must exercise care and hold the workpiece
firmly to prevent it slipping which could result
in your hands coming into contact with the
grinding/sanding belt.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Anl_H_DS_400_SPK7.indb 16 Anl_H_DS_400_SPK7.indb 16
GB

4. Technical data

Voltage ............................................230V ~ 50Hz
Power ....................................... 375 W S2 30 min
Idle speed n .......................................1450 min
0
Grinding/sanding disk Ø ........................ 150 mm
Tilting range of grinding/sanding table ..... 0°-45°
Cross stop .......................................- 60° to + 60°
Belt grinding/sanding device ...............................
Belt speed v .......................................276 m/min
0
Dimensions ................................... 915 x 100 mm
Weight .........................................................12 kg
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (375 W)
for no longer than the time stipulated on the spe-
cifi cations label (30 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ........................ 79 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 92 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
- 16 -
-1
≤ 2.5 m/s
2
h
2
05.09.2016 10:02:07 05.09.2016 10:02:07