General Safety Information - Simer 2956 Manual Del Usuario

Bombas sumergibles para sumideros
Ocultar thumbs Ver también para 2956:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Safety • Specifications
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the product. Save this manual
for future reference.
This is the safety alert symbol. When you
see this symbol on your pump or in this manual,
look for one of the following signal words and
be alert to the potential for personal injury!
indicates a hazard which, if not
avoided, will result in death or serious injury.
indicates a hazard which, if not
avoided, could result in death or serious injury.
indicates a hazard which,
if not avoided, could result in minor or
moderate injury.
NOTICE addresses practices not related to
personal injury.
Description
This submersible sump pump is designed for
home sumps. Unit is equipped with a 3-prong
grounding-type power cord. Shaded-pole motor
is oil filled and sealed for cooler running. Sleeve
bearings on motor shaft never need lubrication.
Automatic reset thermal protection.
Specifications
Power supply required .................................. 115V, 60 HZ.
Liquid Temp. Range ......................... 32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ............15 Amps
Discharge: ...................................................... 1-1/2" FNPT
NOTICE: This unit is not designed for
applications involving salt water or brine! Use
with salt water or brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed as a swimming pool drainer.
Performance
Total Feet (m) of Lift
Series
5 (1.5)
10 (3)
Capacity Gallons/Hour (L/H)
2,760
2,160
2956
(10,448)
(8,176)
3,200
2,700
2958
(12,113)
(10,221)
Electrical & Switch Specifications
Motor
Full Load
Series
HP
(Amps)
2956
1/3
9
2958
1/2
5.5
For parts or assistance, call Simer Customer Service at 1-800-468-7867
15 (4.6)
20 (6.1) No flow
at height
shown
below
1,410
20'
-
(5,337)
(6.1 m)
2,000
1,200
24'
(7,571)
(4,542)
(7.3 m)
*Switch Setting in inches
Water Level For:
On
Off
7.5"
3"
(19.1 cm)
(7.6 cm)

General Safety Information

Electrically powered sump pumps normally
give many years of trouble-free service when
correctly installed, maintained, and used.
However, unusual circumstances (interruption
of power to the pump, dirt/debris in the sump,
flooding that exceeds the pump's capacity,
electrical or mechanical failure in the
pump, etc.) may prevent your pump from
functioning normally. To prevent possible
water damage due to flooding, consult your
retailer about a secondary AC sump pump, a
DC backup sump pump, and/or a high water
alarm. See Troubleshooting in this manual
for information about common sump pump
problems and remedies. For more information,
see your retailer, call Simer customer service
at 1-800-486-7867 or visit our website
at simerpump.com.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before
servicing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump.
An unsecured discharge line will whip,
possibly causing personal injury and/or
property damage.
7. Check hoses for weak or worn condition
before each use, making certain that all
connections are secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance
as required.
9. Provide means of pressure relief for pumps
whose discharge line can be shut-off
or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when
working with pumps.
b. Keep work area clean, uncluttered and
properly lighted – replace all unused tools
and equipment.
c. Keep visitors at a safe distance from
work area.
d. Make workshop child-proof – with
padlocks, master switches, and by
removing starter keys.
11. When wiring an electrically driven pump,
follow all electrical and safety codes
that apply.
2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2958

Tabla de contenido