Principle Of Operation; Transportation And Storage; Cleaning And Maintenance - Expondo RCSM-220-160 Manual De Instrucciones

PRINCIPLE OF OPERATION

RCSM-350-250, RCSM-350-300, RCSM-350-400P,
RCSM-500-400, RCSM-500-300P, RCSM-500-400P,
RCSM-500-500P, RCSM-500-WP
2
3 1
1. Power cable
4 2. Safety button
5
3. Speed adjustment knob: only with
the following models: RCSM-350-
6
400P (1394), RCSM-500-300P
(1396), RCSM-500-400P (1397),
RCSM-500-500P (1398), RCSM-
7
500-WP (1399)
4. ON / OFF switch
8
5. Lock button
6. Carbon brushes cover
7. Blending arm locking nut
8. Blending arm
9
9. Blade
Operating principle
• RCSM-220-160(1390): To start the device, press and hold the ON/OFF switch. To stop the device,
release the ON/OFF switch.
• RCSM-350-250(1392), RCSM-350-300(1393), RCSM-350-400P(1394), RCSM-500-400(1395), RCSM-
500-300P(1396), RCSM-500-400P(1397), RCSM-500-500P(1398), RCSM-500-WP(1399): To start the
blender, press the safety button and then the ON/OFF switch. In order to turn the device off, release
the ON/OFF button. For the device to operate without the need to hold down the ON/OFF switch,
press the lock button with the device on. To release the lock and turn the device off, press and release
the ON/OFF button - the lock will disengage and the device will turn off.
WARNING! Before using the device, make sure the lock switch is not activated and the ON / OFF switch
is on the OFF position.
WARNING! Before using this device, make sure the speed knob is set to the slowest option (turn it
anticlockwise as far as it will go).
ASSEMBLY / DISASSEMBLY OF THE DEVICE'S ELEMENTS:
RCSM-220-160: Align the blending arm
with the blender and turn as far as possible
anticlockwise:
10
RCSM-220-160
1
2
3
1. Power cable
2. ON / OFF switch
4
3. Blending arm
4. Blade
RCSM-350-250, RCSM-350-300, RCSM-350-400P,
RCSM-500-400, RCSM-500-300P, RCSM-500-
400P, RCSM-500-500P, RCSM-500-WP: Insert the
blending arm into the blender and push in:
Rev. 27.04.2017
Make sure that the pen is inserted
into the corresponding position:

TRANSPORTATION AND STORAGE

During transport, the machine should be protected from shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any corrosive gas.

CLEANING AND MAINTENANCE

• Always unplug the device before cleaning it and after each use.
• Use cleaner without corrosive substances to clean surface.
• After cleaning the device, all parts should be dried before reusing it.
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
• Never spray the device with water jets.
CHECK REGULARLY THE DEVICE
Regularly check the machine for signs of damage. If the machine is damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, take a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you
give a detailed and precise description of the matter. The more detailed your information, the better
customer service will be able to solve your problem rapidly and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to
a loss of warranty!
Rev. 27.04.2017
Rotate the nut as far as possible:
11