Safety Instructions; General Information; Technical Data; Installation Instructions - Steinbach Speedsolar Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
EN

Safety instructions

Read through these instructions carefully before you use the
product.
Caution: Failure to comply fully with our instructions for use, or
safety instructions, may cause damage to the unit or injury to
individuals.
 Please read the instruction manual and the directions shown
there.
 Do not allow children to handle this equipment.
 Always turn off your filter system when you are working with your
solar collector.
 Do not position the equipment too close to the pool (adequate
safe distance).
 Do not use any petroleum-based lubricants. Petroleum attacks
the product's plastic components.
 This equipment is not intended for use by anyone (including
children) with restricted physical, sensory or mental ability, or
with limited experience and / or limited knowledge, unless they
are supervised by someone responsible for their safety, or they
receive instruction from them regarding the use of the equip-
ment.
 Children must be supervised to ensure they do not play with the
equipment.
1

General information

1.1.1
Conditions for the installation of a solar collector
The solar collector you have purchased is intended for use with in-
ground and above-ground pools, and is easy to install and handle.
The installation instructions are based on the following conditions:
1) You have a pool which is fully built and filled with water.
2) Your pool has a filter system.
3) You have the required connector hoses to supply the pool and
filter system with water. (Ø 32/38 mm)
These are the requirements so that the solar collector can force wa-
ter through the solar chambers when it is installed and fully connect-
ed to the filter pump.
1.1.2
Use(Figure 1)
Once the equipment is installed, it is connected between your filter
system and your pool using the two hose connectors. The connector
hose forces the cold water from your filter unit into the solar cham-
bers of your solar collector. Here it is heated by the sun's energy and
then fed on to the second connector hose towards the pool.
A = feed from the filter unit to the solar collector
B = feed from the solar collector to the swimming pool inlet nozzles
Water heating depends on the following factors: Flow rate and level
of sunshine.
Solar heating only functions efficiently in sunshine. It can also re-
main connected to the pump in poor weather as this only causes a
slight loss of pressure in the pump.
1.1.3
Tools and accessories required
These tools are required for assembly, but are not included in your
set:
 Phillips screwdriver
 Flat head screwdriver
Page 4 of 30
1.1.4
The ideal location for your solar collector
You solar collector needs to be in a location with as much sunlight
as possible.
 Never position the solar collector over the surface of your pool.
 Keep it an adequate distance away from your pool (keep a safe
distance).
 The solar collector is designed to allow maximum possible pene-
tration of sunlight.
1.1.5
Product care
The solar collector should not be exposed to cold weather. The solar
collector should be stored in an area protected from frost before the
first frost, or at the end of the pool season.
All parts must be rinsed or cleaned with water only. Detergents may
damage the protective cover.
1.1.6
Over wintering
Drain all the water from the solar collector by closing off the pipes.
Store the equipment away for winter in an area protected from frost.
Remove the pool return pipes.
Make sure there is no water left inside the equipment as this can
freeze. Water expands as it freezes and so can damage the solar
chambers.
2

Technical data:

2.1.1
Model 049110 Speedsolar solar collector deluxe
 Dimensions: L x W x H 78 x 78 x 42
 Maximum pressure 2 bar at 20 °C
 Water flow rate max. 10,000 l/h
 Water content collector 10 l
3

Installation instructions

3.1.1
Assembly instructions
Model 049110 Speedsolar solar collector deluxe
Connection between solar collector and pool
For pools with a Ø 32 mm or Ø 38 mm swimming pool hose, follow
the instructions below:
Attach the hose to the return connector on the underside of
the solar collector.
Use a hose clip to connect the hose to the return connector
(see Fig. 13)
A: Pool return hose
B: Reduction fitting, if required
C: Hose clip
D: Return connector
For large INTEX pools (which have swimming pool hoses with gate
valves), follow the instructions below (Fig. 14):
Connect the INTEX special adapter and the O ring with the
return connector. Make sure the O ring is in the INTEX spe-
cial adapter.
Screw on the pool hose with the INTEX special adapter
Make sure that the seal between the hose and the INTEX
special adapter is correctly inserted.
A: INTEX special hose
B: INTEX special adapter
C: O ring
D: Return connector
Speedsolar Sonnenkollektor | 2015_V1

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido