Additional Safety Rules For Cordless Drills / Drivers; Know Your Product; Operation - Normfest ASA18V Instrucciones De Uso

5. BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fire.
d) Under abusive conditions, liquid may be eject-
ed from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
6. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Additional safety rules
for cordless drills / drivers
▪ Be aware that this tool is always in an operating condi-
tion, because it does not have to be plugged into an
electrical outlet. Always set the trigger switch to the
locked OFF position when installing or removing the
battery pack.
▪ Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
▪ Use the auxiliary handle if supplied with the ma-
chine. Loss of control can cause personal injury.
▪ Hold the power tool by insulated gripping sur-
faces when performing an operation where the
cutting accessory or the fastener may contact
hidden wiring. Contact with a "live" wire will make
exposed metal parts of the power tool "live" and shock
the operator.
▪ If possible, always use clamps or a vice to hold your
work.
▪ Do not touch the bit after operation. It will be very hot.
▪ When using the drill, use safety equipment including
safety glasses and ear defenders. Wear a dust mask
if the drilling operation creates dust.
▪ The dust, separated while processing materials, con-
taining quartz (SiO
not process materials containing asbestos.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the oper-
14
EN
) is dangerous to your health. Do
2
ating instructions to be found in this Manual. All per-
sons who use and service the machine have to be
acquainted with this Manual and must be informed
about its potential hazards. Children and frail people
must not use this tool. Children should be supervised
at all times if they are in the area in which the tool is
being used. It is also imperative that you observe the
accident prevention regulations in force in your area.
The same applies for general rules of occupational
health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Even when the tool is used as prescribed it is not pos-
sible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool's construc-
tion and design:
▪ Damage to the lungs if an effective dust mask is not
worn.
▪ Damage to hearing if effective ear defenders are not
worn.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Keyless chuck
2. Speed selector switch
3. Forward/reverse switch
4. Battery release button
5. Battery
6. ON/OFF trigger switch
7. Battery state indicator
8. LED light
9. Torque adjustment collar
10. Charger

Operation

The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal, ceramics
and plastic.
FITTING AND REMOVING THE
BATTERY PACK (Fig. 1)
To remove the battery: Press release button (4) in the
indicated direction (A) and pull the battery out of the ma-
chine body. (B)
WARNING: Always set the forward/reverse
switch (3) in central position before any work on the
machine e. g. fitting and removing a battery, tool
change, transport, maintenance and storage.
ASA18V