Normfest ASA18V Instrucciones De Uso página 17

To insert the battery: Place the battery into the base of the
machine and slide it until it locks with an audible click. (C).
BATTERY STATE INDICATION (Fig. 2)
The battery state during operation can be checked on
the LED display (7) by pressing the ON/OFF trigger
switch (6).
Depending on the number of illuminated LEDs the bat-
tery state is as follows:
3 Battery capacity: 60 - 100%
2 Battery capacity: 30 - 60%
1
Battery capacity: < 30%
1 Battery capacity: < 20%. The battery
Blinking light
must be recharged.
Problems with battery. The display is
Blinking light activated upon pressing the trigger of
the switch. It may show one of the fol-
lowing battery states:
▪ Low battery ► Battery has to be
recharged;
▪ Temperature
been actuated ► Battery must
be cooled down prior to resuming
operation;
▪ Damaged or unrecognized bat-
tery ► Battery has to be replaced
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
LED WORK AREA LIGHT
The machine is equipped with LED light (8) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. To turn the LED light on press the
trigger of switch (6). LED light will automatically turn off 5
seconds after releasing the trigger of switch (6).
Electronic control may turn off the excessively overload-
ed machine in order to protect it. This mode is signalled
by blinking LED work area light (8). The power tool can
be used for its intended purpose after switching it on
again.
REVERSING (Fig. 3)
The extreme position of forward/reverse switch (3) to the
right (viewed from the rear) is equivalent to anti-clock-
wise rotation, the extreme position to the left - to clock-
wise rotation. When the ON/OFF switch (6) is depressed
switch (3) cannot be actuated.
With the ON/OFF switch (3) in neutral position, switch (6)
cannot be pressed and the machine cannot be operated.
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
SWITCHING ON - SWITCHING OFF
Switching on: press ON/OFF switch (6).
Switching off: release ON/OFF switch (6).
Original instructions
This power tool is equipped with electric brake. The spin-
dle stops rotating immediately after releasing the switch
lever.
SMOOTH ELECTRONIC RPM CONTROL
Light pressure on ON/OFF trigger switch (6) results in
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
ADJUSTING THE TORQUE (Fig. 4)
Rotate the torque adjustment collar (9) behind the chuck,
to adjust the torque to each of 20 settings.
The range of 20 torque settings allows better control
when using the drill as a screwdriver thus preventing
over-tightening of the screws.
The numbers circling the collar are used to indicate the
level of torque. The larger the number on the collar, the
higher the torque. To select any of the numbers, rotate
the collar (9) until the desired number aligns with the ar-
protection has
row head indicator on the housing of the machine.
1
÷
20
SPEED SELECTOR SWITCH (Fig. 5)
The two-speed selector switch (2) enables you to select
the appropriate gear with the optimum speed and torque
to suit the application.
the drill is switched off.
1. To select the low gear (low speed, high torque
2. To select the high gear (high speed, low torque
INSERTING AND REMOVING BITS (Fig. 6)
ward/reverse switch (3) in central (neutral) position (A).
Screwdriving
Set the torque adjustment collar (9) against one
of 20 positions.
Select low setting range for working with small
screws or in soft materials.
Select high setting range for working with large
screws or in hard materials.
Drilling
Set the torque adjustment collar (9) against this
symbol to choose drilling in metal, wood, etc.
The power tool is equipped with an electric
brake. The spindle stops rotation immediately
after the switch trigger has been released. At
overloading in drilling mode release the switch
immediately to prevent prolonged overloading
and overheating the motor.
WARNING: When changing the gear ensure
setting), push the gear selector (2) backward. The
digit 1 on the switch will be displayed.
setting), push the gear selector (2) forward. The digit
2 on the switch will be displayed.
WARNING: Remove the battery or set the for-
15
EN