Technical Data; Important; Before Putting Into Operation - Gardol GAF-E 20 Li OA Manual De Instrucciones

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.

4. Technical data

Speed n ..............................................1200 min
0
Max. brush diameter ...................... ......... 100 mm
Protection class ................................................III
L sound power level ............................... 77 dB
WA
L sound pressure level ............................ 57 dB
pA
K uncertainty ................................................. 3 dB
Vibration ...............................................≤ 2.5 m/s
K uncertainty .......................................... 1.5 m/s²
Weight ..................................................... 1.85 kg
Sound pressure level
at the operator's ear ............................... 64 dB(A)
K uncertainty ................................................. 3 dB

Important!

The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
20 V, 1.5 Ah .............................. 5 lithium-ion cells
20 V, 3.0 Ah ............................ 10 lithium-ion cells
20 V, 4.0 Ah ............................ 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Charging unit
Mains voltage ................... 200-250 V ~ 50-60 Hz
Output
Rated voltage ........................................ 21 V d. c.
Rated current ....................................... 3000 mA
The machine noise might exceed 85 dB (A). The
operator will require noise protection measures
if this is the case. The noise is measured in ac-
cordance with prEN ISO 10518. The value of the
vibrations emitted by the handle was determined
in accordance with prEN ISO 10518.
Anl_GAF_E_20_Li_OA_SPK7.indb 17 Anl_GAF_E_20_Li_OA_SPK7.indb 17
GB
Important.
The vibration value changes according to the
area of application of the electric equipment and
may exceed the specifi ed value in exceptional
circumstances.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect condi-
tion.
-1
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
2
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before putting into operation

The equipment is supplied without batteries
and without a charger.
5.1 Assembly (Fig. 3-6b)
Connect the upper part of the housing and the
bottom part of the housing together (Fig. 3).
Slot the guide wheel (Fig. 4/Item 7) into the guide
on the housing (Fig. 4/Item A).
Make sure that there is an audible click when they
engage.
Fit the guard hood (Fig. 5/Item 6) as shown in Fi-
gure 5 and secure with 2 screws (Fig. 5/Item. 13).
Fit the brush (Fig. 6a/Item A) onto the drive axle
(Fig. 6a/Item B). Make sure that the brush fi ts ac-
curately into the mount (Fig. 6a/Item C). The shaft
must be fi xed in order to fasten the brush. To do
so, insert the pin (Fig. 2/Item 10) into the recess
on the shaft (Fig. 6b) and hold with one hand.
- 17 -
03.08.2017 11:30:16 03.08.2017 11:30:16