EURO-PRO Shark S3202 Manual Del Usuario página 4

Trapeador a vapor de lujo
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATING INSTRUCTIONS
How To Assemble Your Steam Mop
1. Remove all the parts from the
packaging.
2. Insert the upper extension
tube into the lower
extension tube. (Fig. 1)
Push it in until you
hear it click into place.
3. Insert the extension
tube assembly
into the pump
actuator. Make
sure that the
locking tab snaps
into place.
(Fig. 1)
actuator
4. Place the micro-fiber
cleaning pad
underneath the
mop head. Make
sure that the hook
and latch strips are
Fig. 1
facing up. (Fig. 2)
Press to secure.
TIP:
The micro-fiber
cleaning pads have
a colored tab so that
a different pad can
be assigned
to different
Hook & latch
tasks or
strips
rooms in
Fig. 2
the house.
Filling the Water Tank
IMPORTANT:
Always insure that the
unit is "UNPLUGGED" from the wall
receptacle prior to initial filling and before
attaching the micro-fiber cleaning pad to
the bottom of the mop head. Never use
the steam mop without the micro-fiber
cleaning pad attached to the mop head.
NOTE
: When using the steam mop for
the first time you may notice water residue
inside the unit. Water drops may also be
found in the packaging. This is normal
and you should not be alarmed. Each
steam mop is 100% factory tested to
insure product performance and safety.
Some water may be left in the unit from
these test procedures.
1. Turn the cap
counter clockwise
and then lift up to
remove from the
water tank.
(Fig. 3)
2. Using the filling
flask and funnel,
pour one flask of water into the water
tank. Do not overfill the unit.
3. Replace the cap onto the water tank.
Using the Steam Mop
IMPORTANT:
Never use the steam
mop without the micro-fiber cleaning pad
Pump
attached to the mop head or without water
in the water tank.
Please note that when using for the first
time, the appliance may take longer than
the normal 30 second startup time to
steam. You may need to pump the
handle a few times before the steam is
released. This is due to the water making
its way from the water tank through the
pump and into the heater. This will only
occur during the first use.
Mop
1. Sweep or vacuum floors before using
head
the steam mop.
2. Twist the quick release cord holder to
unwrap the power cord completely.
3. Plug into a 120-volt electrical outlet.
4. The power "On" light will turn green.
5. It takes approximately 30 seconds for
the unit to heat up and the steam to be
ready.
6. Pump the handle a few times to
dampen the micro-fiber cleaning pad.
Begin mopping with a forward and
backward motion, this pumping action
will release steam as you mop.
7. When the water tank is empty, the
steam mop will stop emitting steam.
Unplug the power cord from the
electrical outlet and refill the water tank
following the instructions above.
8. When you have finished using the
steam mop, unplug the unit from the
electrical outlet and carefully remove
the micro-fiber cleaning pad from the
mop head. Please note that the micro-
fiber cleaning pad gets very hot with
the steam. Always use caution when
removing.
5
9. Never leave the micro-fiber cleaning
pad on the steam mop head when you
have finished using the steam mop.
Always remove the micro-fiber
MAX
cleaning pad and wash in warm water
with a mild detergent. Never use
bleach or fabric softener when
Fig. 3
washing the reusable micro-fiber
cleaning pad. The micro-fiber
cleaning pad may be washed in a
washing machine and dried in a
clothes drier on low heat. We
recommend that you air dry.
IMPORTANT:
Be careful when machine
washing or drying with mixed fabrics as
micro-fiber pads will pick up lint from other
fabrics and the hook and latch strips will
stick to other garments. We recommend
washing the micro-fiber cleaning pads
separately or placing them in a garment
bag first.
CAUTION:
Never store the steam mop
with a wet or damp micro-fiber cleaning
pad still attached as this will damage your
floors.
Using the Carpet Glider
The amazing carpet glider accessory
allows you to freshen and deodorize all
your carpets and rugs with the
sanitizing power of steam!
To use:
1. Attach the mop head to the
micro-fiber cleaning pad.
2. Place the mop head, with
cleaning pad attached, on
top of the carpet glider.
Please note that the steam
mop rests on top of the
carpet glider and is not a
fixed attachment. (Fig. 4)
Mop Head
Micro-Fiber
Cleaning Pad
Carpet
Glider
Fig. 4
OPERATING INSTRUCTIONS
3. Plug the power cord into a 120-volt
electrical outlet.
4. Begin freshening your carpet or rug by
pushing the mop and glider in a
forward and backward motion,
releasing steam as you go.
5. When you have finished freshening
your carpet or rug, unplug the steam
mop and remove the mop from the
carpet or rug.
NOTE:
Move the mop and carpet glider
along the carpet or rug in a continuous
motion until you are finished. This
product is not intended to be used as a
carpet cleaner, only a carpet freshener or
deodorizer. DO NOT leave the mop in
one stationary position.
IMPORTANT:
carpets and rugs thoroughly before using
the steam mop.
DO NOT use without the following:
the carpet glider under the mop head
a micro-fiber cleaning pad attached to
the mop head
water in the tank
ALWAYS insure that the unit is
"UNPLUGGED" from the electrical socket
prior to filling the tank with water and
attaching the micro-fiber cleaning pad to
the bottom of the mop head.
NOTE:
When using for the first time,
water in the tank must make its way
thought the pump to the heater. In order
to initiate the process, you may be
required to pump the handle a few times
to release the steam.
Care & Maintenance of the
Micro-Fiber Cleaning Pad
Due to the unique cleaning ability of
this pad, proper care of your micro-
fiber cleaning pad is required to
ensure long life and continued
cleaning ability.
The first thing you should do when
you get a new micro-fiber cleaning
pad is to wash and dry it. During
the manufacturing process the
fabric has a tendency to become
flat as it picks up contaminants
from the air and machinery. There
will also be a number of loose
threads that, while they cause no
harm, can be annoying the first
time you use the pad.
6
ALWAYS vacuum

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Shark s3202c

Tabla de contenido