Use Of Accessories; Emptying The Dust Collector - Livington Prime Everyday Instrucciones De Uso

never be allowed to play with the device.
Cleaning and user maintenance must
never be performed by children without
supervision.
USE
Before first use: remove all packaging material and
protective films. Do not remove the type shield from the
product. Check that the delivery contents are complete,
and ensure that there is no damage to the product and that
it is assembled correctly. If any damage is evident, refrain
from using the device and contact our customer services
(see details on the back).
Charging (# 2 + 3)
1. Make sure that the device is turned off.
2. Connect the narrow end of the USB cable to the USB
socket on the universal vacuum cleaner, and connect
the wide end of the USB cable to the power adapter.
Plug the power adapter into an electrical outlet.
3. During the charging process, the LED indicator and
the battery charge indicator will flash blue (charging
time: approx. 3-4 hours)
4. As soon as the battery is fully charged, both
indicators light up continuously in blue and the
device can be disconnected from the power supply.
Note:
• As soon as the battery charge is low, the LED display will
start to flash. You should charge the device as soon as
possible.
• If the device is not used for a long time, the battery
charge level drops; please charge the battery once or
twice every six months.
Switching on & off and regulating the power
1. Switching on: Press the On/Off button to switch on
the universal vacuum cleaner. The blue operating
light comes on. The device will run at the first
power level. Note: After you have pressed the On/
Off button, there will be a 1-2 second delay before
the motor develops its full power. This is a safety
measure, and is not a defect.
2. Controlling the power: Press the +/- button once to
activate the higher power level. To switch back to the
initial power level, press the +/- button again.
3. Switching off: Press the On/Off button again to
switch off the device. The operating LED switches off
with the device.

USE OF ACCESSORIES

Crevice nozzle (#4) / Brush nozzle (#5) / Long flexi nozzle (#6)
1. Insert the desired attachment into the suction
opening of the device, pushing it as far as it will go.
Crevice nozzle: cleaning of joints, chair slats, car
interiors, corners, etc.
Brush nozzle: cleaning of sofas, armchairs,
scratching posts, animal beds, sensitive surfaces, etc.
Long flexi nozzle: To assemble the flexi nozzle, slide
the end piece onto one end and the connector onto
the other end of the flexi nozzle pole. Make sure that
both parts are firmly fastened. Tip: If you are having
M24329 / M24330_livington_prime_everyday_Manual_20200723_MM.indd 10 M24329 / M24330_livington_prime_everyday_Manual_20200723_MM.indd 10
problems attaching the parts, try briefly immersing
the pole in warm water to slightly soften the material.
The water should not be too hot, to avoid deformation
of the pole. Dry the pole before assembling the flexi
nozzle.
The flexi nozzle is suitable for cleaning hard-to-reach
areas, such as curtain rods, narrow spaces etc.
2. Switch on the device at the desired power level. We
recommend the lower power level for the cleaning of
upholstered furniture.
3. Switch the vacuum cleaner off after use and remove
the nozzle. Remove any dirt residue such as hair and
lint from the brush nozzle immediately after use.
The crevice nozzle and brush nozzle can be easily
attached to the storage station.

EMPTYING THE DUST COLLECTOR

Note: To prevent blockages and a decrease in the suction
power, we recommend emptying the dust collector after
each use.
Rapid emptying (# 7+8)
1. Turn off the device.
2. Hold the vacuum cleaner with the suction opening
facing down over a waste bin.
3. Press the rapid emptying button on the container to
easily and conveniently empty the dust collector.
4. Fold the lid of the dust collector back down again
until it firmly clicks into place. Make sure that the
container is tightly closed.
Dust collector removal (# 9)
To entirely remove coarse, stubborn dirt from the dust
collector, you can remove the entire container and rinse it
off. Make sure that the container is completely dry before
you re-attach it to the device.
1. Switch off the universal vacuum cleaner.
2. Hold the vacuum cleaner with the suction opening
facing up.
3. Press the release button once, and remove the dust
collector.
4. Now grasp the small metal bracket on the filter
unit and pull the unit out. Now simply empty the
container, and rinse if necessary. Alternatively, you
can also press the rapid emptying button.
Note: Only rinse the dust collector after the filter unit has
been removed.
FILTER REPLACEMENT/CLEANING (# 10-11)
1. Make sure that the device is switched off.
2. Remove the dust collector from the device as
described above.
3. Now remove the filter unit from the container by
folding up the small metal bracket on the unit and
pulling on it.
Separating the filter: Hold the metal bracket with
4.
one finger; the plastic cover of the stainless steel
filter should face upwards. Paying attention to
the markings on the stainless steel filter, turn the
stainless steel filter slightly to the left (direction
„open lock") and separate the filters. Now you can
remove the hepa filter and clean the filters.
Inserting a new hepa filter: To insert a new hepa
5.
filter, place it in the stainless steel filter (pay attention
to the brackets inside the stainless steel filter). Now
10
23.07.20 15:58 23.07.20 15:58