Mitsubishi Electric PAC-IF011B-E Para El Instalador página 6

3. Electrical work
3.1.4. Connecting external input
Demand control is available by external input.
It is possible to set the outdoor unit's power consumption by setting the switch of the interface controller.
Switch1, Switch 6 : Input selection of inverter capacity setting
Input SW 1-1 SW 1-2 SW 1-3 SW 6-1 SW 6-2
REMOTE SWITCH
OFF OFF
Type A (4bit-8 setting)
REMOTE SWITCH
ON OFF
Type B (1bit-1 setting)
4-20mA ON ON
1-5V ON ON
0-10V OFF OFF
0-10kΩ ON OFF
No input (AUTO mode) OFF ON
• REMOTE SWITCH Type A (4bit - 8 setting) / Type B (1bit -1 setting)
TB142 TB142 TB142
10-11 10-12 10-13
(COM-IN5) (COM-IN6) (COM-IN7)
OFF OFF OFF
ON OFF OFF
OFF ON OFF
ON ON OFF
OFF OFF ON
ON OFF ON
OFF ON ON
ON ON ON
OFF OFF OFF
TB62
Photo.3-5
TB142
• External function setting
This function is setting operation mode or stopping compressor, by the external signal.
TB142 Item
1-2 (IN1) Forced Comp. OFF
3-4 (IN2)Item Fixed operation mode Cooling
Cable length : Maximum 10m
Remote switch : Minimum applicableload DC12V, 1mA
Caution:
The external input signals are separated by basic insulation from power supply for the unit.
The external input signals should be separated by supplementary insulation from where user may touch in case that it is installed where
user may touch.
Connect the terminals by using the ring terminals and also insulate the cables of adjoining terminals when wiring to terminal block.
6
Step for capacity setting
OFF OFF OFF OFF/Step1/Step2/.../Step7/Auto
OFF OFF OFF OFF/Step1/Step4/Step7/Auto
OFF ON ON OFF/Step1/Step2/.../Step7
OFF OFF ON OFF/Step1/Step2/.../Step7
ON OFF OFF OFF/Step1/Step2/.../Step7
ON OFF OFF OFF/Step1/Step2/.../Step7/Auto
ON OFF OFF Only Auto mode
TB142
Step for capacity setting
10-14
TypeA
(COM-IN8)
OFF [OFF] OFF 0%
OFF [ON] Step1 10%
OFF Step2 20%
OFF Step3 30%
OFF Step4 50%
OFF Step5 70%
OFF Step6 80%
OFF Step7 100%
ON Auto
At site I/F
{ 10
11
OFF∼AUTO 12
13
14
TB142
OFF ON Remark
Normal Forced Comp. OFF
Heating Available when SW2-1 and SW2-2
are ON
Remark
TypeB
[OFF] OFF 0%
OFF
[ON] Step1 10%
Step4 50%
Hz fixed
Step7 100%
mode
Auto mode
Auto
At site I/F
10
11
Step1
12
Step4
13
Step7
14
AUTO
TB142
Demand control is available by connecting remote switches with terminal No.10 - 14.
Make sure to use the non-voltage switch (for the remote switch)
Remote switch cable length : Maximum 10m
Remote switch : Minimum applicable load DC12V, 1mA
• 4-20mA / 1-5V / 0-10V / 0-10kΩ
1Use 4-20mA / 1-5V / 0-10V
Connect the transmission cables to No. 3 and 4 on the terminal block (TB62).
No. 3 on the terminal block(TB62) : Plus side
No. 4 on the terminal block(TB62) : Minus side (Reference side)
2Use adjustable resistor (0-10kΩ)
Connect the transmission cables to No. 1 and 2 on the terminal block (TB62).
Adjustable
resistor 4-20mA
(0-10kΩ)
0~100Ω 4~5mA 0~1.25V
510Ω 7mA 1.75V
1kΩ 9mA 2.25V
2kΩ 11mA 2.75V
3.3kΩ 13mA 3.25V
4.3kΩ 15mA 3.75V
5.6kΩ 17mA 4.25V
7.5kΩ 19~20mA 4.75~5V
10kΩ –
OPEN(12kΩ~) –
*The value of the above-mentioned table becomes the center of the input value.
Cable length : Maximum 10m
Wired remote controller
Step for
1-5V 0-10V capacity
setting
0~0.63V OFF 0% Stop
1.88V Step1 10%
3.13V Step2 20%
4.38V Step3 30%
5.63V Step4 50%
6.88V Step5 70%
8.13V Step6 80%
9.38~10V Step7 100%
– – Auto
– – OFF 0% Stop
At site I/F
I/F
1
0-10 kΩ
2
3
+
4-20mA/1-5V/0-10V
4
At site
5
6
(For maintenance)
TB62
Remark
Hz fi xed
mode
Auto mode
TB142
1 2 3 4