Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Review this chart to find do-it-yourself
solutions for minor performance
problems, Any service
needed, other than those described
in this owner's manual, should be performed by a Sears
authorized
service representative.
Cleanerwon't start.
Poor job of dirt
1.
ptck-up,
2.
3o
4.
5.
6.
7,
B,
9°
1Do
Cleanerstarts but
1.
cuts off.
2.
Power-Mate=wilt not
run when attached.
Performance indicator,
1.
some models, is red,
2.
3,
4.
Cleaner picks up moveable
rugs -or. Power-Mate"
pushestoo hard.
Lightwon't work,
Cordwon't rewind.
Cleaner leaves marks
on carpet,
t
1. Unpluggedat wa{loutieL
2. Tripped circuitbreaker/blownfuse
at household service panel.
3. Loose hose electrical connections,
3,
4o Tripped thermal protector in
4.
canister.
Full or cloggeddust bag.
1.
Clogged airflow passages.,
2.
Dirty filters.,
3,
Wrongpile height setting,
4.
Open suctioncontrol.
5,
Hole in hose.
6,
Worn Power-Mate _ brushes,
7.
Worn or broken beIt.
8 & g,
Dirty brush or brush supports.
Canister hood open.
Hose or hood electricalconnections.
Tripped overload protector in
Power-Mate ® .
3. Tripped thermalprotector
3.
in canister,
I.
Power-Mate connections
1.
unp{uggedo
2. Worn or broken belt,
2 & 3,
3. Dirty brush or brush supports.
4. Tripped overload protectorin
4.
Power-Mate 1..
Fultor clogged duel bag,
Dirty litters.,
Clogged aidlow passage,
Certain attachmenttooled,
I. Plug In lirmly, push ON!OFF switch toON.
2. Reset clmuit breaker or replacefuse,
Reconnecthose ends, (page 7).
Resel thermatproteclor,(page 11)_
Change bag, (page 13)
Clear airllow passages, (page 13).
Clean!changefillers, (page 14, 15)_
Adjustselling, (page 9)_
Adiust control,(page 12)
Replacehose.
Change brushes, (page I8).
See BELTCHANGING AND BRUSH
CLEANING, (pages 16, 17),
10. Close and latch hood.
1. Check connections,reconnect hose
ends, (page 7).
2. Removeany items thaimay be caught
or jammed, thenreset, if cleaner stads
and stops again, clean brush and brush
supports, thenreset, (pages 16, I7),
Reset thermal protector, ( page 11),,
Plug in firmly, (page 6).
_ .....................................................
2_
3_
4_
See BELTCHANGING AND BRUSH
CLEANING,(pages 16, t7).
Check brush area for excessive lint
buiid-upor jamming.Clean brush and
brush supports, then reset, (pages 16, t7)o
Change bag, (page 13)°
Clean!changefillers, (page 14, 15).
Clear clog from airflow passage, (page 13),
This is normaLRedshould disappear
when tool is removed,
1, Wrong pile"f_eigh'i"seiting '...................
1. 'Adjust setting, (page 9).
"'
2. Suction too strong.
2o Open suction control,(page 16)o
!. Burned out light bulb
1. Change light bulbl (page 16),,
1. Dirty power cord.,
1. Clean the power cord,
2. Cord jammed.
2. Pullout cordand rewind
I. Wrong ,vacuuming pattern°
' .................
'!'_ See VAc'uUMINGTIPS, [page 9),
18
Publicidad
Tabla de contenido
