Briteq BT-60LS Manual De Instrucciones página 5

ENGLISH
 Once the right mode shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Split Color
You can select if the unit can only show full colors or also
split colors.
 Press the MENU button until "Split color" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "Yes" (Split colors) or "No"
(only full colors).
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master
or to work in complete sync.
 Press the MENU button until "Slave Mode" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select Slave1 (normal) or Slave2
(2 light show) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit
goes in blackout and waits for the DMX-signal.
No blackout mode: when no DMX-signal is detected, the unit
automatically switches to standalone mode.
 Press the MENU button until "Black Out" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "Yes" (blackout on) or
"No" (blackout off) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Sound State
The unit works to rhythm of the beat when used in
standalone or master/slave mode
 Press the MENU button until "Sound State" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "On" or "Off" mode.
 Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the
BRITEQ
®
OPERATION MANUAL
5/89
ENGLISH
MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound Sense
Used to set the sensitivity of the internal microphone
 Press the MENU button until "Sound Sense" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select a value between "0" (very low sensitivity) and "100" (high sensitivity).
 Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until "Pan Inverse" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "No" (normal) or "Yes" (pan inversion) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until "Tilt Inverse" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "No" (normal) or "Yes" (tilt inversion) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Backlight
Backlight on: display is always lit.
Backlight off: display is dark when not used.
 Press the MENU button until the display shows "Back Light".
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select "On" (display always lit) or "Off" (display dark when not used).
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
GOBO1 Adjust
Used to help you adjusting the focus of the rotating gobos (gobo wheel1).
 Press the MENU button until the display shows "Focus1 Adjust".
 Press the ENTER button so the unit goes to the "tilt 90°" position.
 Press the ENTER button so the unit goes to the "pan 0°" position.
 Press the ENTER button so the unit goes to the "pan 90°" position.
 Press the ENTER button so the unit goes to the "pan 180°" position.
 Press the ENTER button so the unit goes to the "pan 270°" position.
In the Previous 5 steps you are able to adjust the focus with the UP/DOWN buttons on the unit (the display
shows the current focus status).
Attention: please note that you can only set an "average focus" for all 5 positions, so it is not possible to set
the focus perfectly sharp for all directions.
 To go back to the functions press the MENU button.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
BT-60LS BRITEQ 6/89
®
OPERATION MANUAL
BT-60LS