Listening To The Ipod Or Iphone; To Insert Ipod Or Iphone Adaptor; To Remove Ipod Or Iphone Adaptor - Pioneer X-HM50-k Manual De Instrucciones

Setting the clock (Remote control
only) (continued)
5
To adjust the hour, press the
press the ENTER button. Press the
once to advance the time by 1 hour. Hold it down to
advance continuously.
6
To adjust the minutes, press the
then press the ENTER button. Press the
button once to advance the time by 1 minute.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will appear
for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock (pages 9 - 10).
To readjust the clock:
Perform "Setting the clock" from step 1. If the "Clock" does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 24 for details.]
2
Perform "Setting the clock" from step 1 onwards.

Listening to the iPod or iPhone

Supported iPod and iPhone models:
st nd rd
l iPod touch (1 /2 /3 /4
l iPod classic
nd rd th
l iPod nano (2 /3 /4 /5
l iPhone 4
l iPhone 3GS
l iPhone 3G
l iPhone
Notes:
l Audio from the iPod/iPhone cannot be heard via the
headphones connected to the unit.
l Once the iPod or iPhone is connected to the unit it will
begin charging.
l Error message "This accessory is not made to work with
iPhone" may appear on the iPhone screen when iPhone
battery is low.
l The message "This accessory is not made to work with
iPhone" or "This accessory is not supported by iPhone"
may appear on the iPhone screen when the iPhone is not
properly docked (eg. slanting) on this product. If this
occurs, please remove and re-dock the iPhone.
l To prevent random interference when iPod/iPhone
function is selected, the headphone output is
disabled.
You may also experience brief audio interference
during incoming calls.
or button and then
or
or button and
th
generation)
th th
/6 generation)
n iPod and iPhone adaptor connection
Notes:
l Please use the adaptor supplied with your iPod or iPhone
unit.
l You can use an audio cable to connect your iPod to the
button
AUDIO IN socket if:
1. your iPod adaptor does not fit into the iPod dock on the
main unit.
or
2. you have an iPod that does not have an iPod adaptor.
3. you have an iPod that does not have an iPod 30 pin
connector.
iPhone
Adaptor No.
12
15
19
n To insert iPod or iPhone adaptor
1
Open the iPod cover by pulling up.
2
Insert the iPod or iPhone adaptor into unit and connect
your iPod or iPhone.
iPhone (bottom)
Dock connector
iPhone connector
Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
n To remove iPod or iPhone adaptor
Insert the tip of a screwdriver ("–" type,
small) into the adaptor hole as shown
and lift upward to remove.
n iPod or iPhone playback
1
Press the STANDBY/ON button to turn the power on.
2
Press the iPod/iPhone button on the remote control or INPUT
button repeatedly on the main unit to select iPod function.
3
Insert iPod or iPhone unit in iPod dock of main unit.
4
Press the
En-10
iPhone
Description
iPhone
iPhone 3G, 8GB & 16GB & 32GB
iPhone 3GS
iPhone 4
iPhone
iPhone adaptor
iPhone dock
/ (iPod/iPhone / ) button to start playback.
Capacity
4GB & 8GB & 16GB
& 64GB
16GB & 32GB