Technical Specification - Prestige MEDICAL 2100 Classic Serie Instrucciones De Funcionamiento

In the unlikely event that something should go wrong, we have incorporated a number of safety features to ensure that your autoclave
remains safe at all times.
Safety features.
1. Located to the rear of the lid, beneath the cover, is a spring
called the Gasket Offset Device (GOD Spring), designed to
prevent pressure building up if the lid has been incorrectly
fitted. DO NOT TAMPER WITH THIS SAFETY DEVICE
2. If for any reason, the temperature falls below the minimum
required sterilizing temperature, resulting in the Sterilizing
Temperature light (L3) switching off, the cycle timer will re-start
from zero once the correct temperature has been restored.
3. If there is an electrical or electronic failure resulting in a build
up of pressure - in excess of normal operating pressure - one or
all of the following safety features will be activated.
i) Depressurization Valve (A) will loudly and rapidly "vent"
steam. On134ºC model only the overpressure Safety Valve
located underneath the handle (G) will loudly and rapidly
vent steam allowing its exit via the Steam Duct (H)
ii) The gasket will "extrude" through the slot in the rear of
the lid rapidly releasing excess pressure and steam.
iii) A non - resettable thermal fuse located in the base of the unit
will "melt' at a pre-determined temperature, disconnecting
the power.
Technical Specifications - Standard Body Autoclaves & 210006
Height..........................335 mm
Width..........................340 mm
Net Weight.........4.5 – 5.6 kilos
Height...........................335 mm
Width...........................340 mm
Net Weight...................5.6 kilos
Height...........................420 mm
Width...........................340 mm
Net Weight...................4.5 kilos
Fuses - Located under the control module, fuses
F10A, 32 x 6.3mm, ceramic sand filled (230v model only),
Mains plug top fuse (User replaceable), F13A to BS1362 UK
ONLY.
Rating - Models are rated continuously for intermittent use.
Body - Deep drawn aluminium.
Lid – Aluminium 121/126 ºC models, 304 Stainless Steel on
134ºC & ASME (21006 FDA 510(K) Number K962903)
units only.
Heater - Externally surface mounted mechanically
fixed electric.
Temperature cit out - thermal fuse.
Pressure - calibrated pressure relief valve.
Capacity...............................9 litres
Internal chamber
Dimensions (d/h)................210/230 mm
- 9 litre -134ºC Body Autoclaves
Capacity................................9 litres
Internal chamber
Dimensions (d/h)..................210/230 mm
-Extended Body Autoclaves
Capacity................................12 litres
Internal chamber
Dimensions (d/h)..................210/270 mm

Technical Specification

Should any of the devices listed activate, please observe the
following steps:
a) Do not touch the unit.
b) Switch off at the wall socket and un-plug
c) Allow temperature and pressure to drop
before
d) Do not attempt to re-start the unit
e) Arrange for an immediate service.
!
Max. Single Fault Temperature - 133.3°C
Over Voltage Category - Group ll
Pollution Degree - Group 2
Environment Conditions - indoor use - temperature 5°C to 40°C -
altitude up to 2000m - maximum relative humidity 80% for
temperatures up to 31°C decreasing linearly to 50% relative
humidity at 40°C. - mains supply voltage fluctuations not to exceed
+10% of the nominal voltage Input Connections - Mains inlet socket
'hot' format conforming to IEC 302.
Safety Shut Down - See 'Temperature Cut Out'.
Packaging - All packaging materials are recyclable.
- 9 -
i) touching the unit
ii) removing your instruments
Max' Instrument
length............................... 228 mm
Max' Load Weight........... 3.0 kilos
Max' Instrument
length...............................228 mm
Max' Load Weight............ 3.0 kilos
Max' Instrument
length...............................290 mm
Max' Load Weight............ 4.0 kilos
(141.0°C on the134°C model)
211641E