Nylon Head - HIKOKI CG 36DA Instrucciones De Manejo

3. Extending the main pipe (Fig. 9)
(1) Release the locking lever to allow the main pipe to be
extended.
(2) Extend the main pipe as far as it will go, making sure that
you hear it click.
NOTE
The motor will not operate unless the main pipe is fully
extended.
When you push the power button, the red power light will
fl ash rapidly.
(3) After extending the main pipe until it clicks, check that
the hole of the holder case is aligned with the hole of the
main pipe and lock the locking lever to fi x the main pipe
securely.
4. Installing cover (See Fig. 10 and 11)
WARNING
Be sure to install the cover in its designated location.
Failure to heed this warning may result in injury from
fl ying stones.
NOTE
Use the supplied hex. bar wrench 4 mm for installation.
(1) Use the supplied D5 tapping screw to install the knife in
the cover. (Fig. 10)
(2) Align the two holes in the cover bracket and the cover
and insert two M6 × 25 hex. socket button bolts. (The
cover bracket is installed in the motor case.)
(3) Place the cover holder on the underside of the cover and
use the supplied hex. bar wrench 4 mm to alternately
tighten the two M6 × 25 hex. socket button bolts until
they are properly tightened.
CAUTION
○ Take care to avoid cutting yourself on the knife inside the
cover.
○ Install the cover and knife properly and securely as
instructed in the handling instructions.
If not attached properly or securely, they may come off
and cause injury.
5. Installing the shoulder belt
Use in combination with a BSL36A18 battery.
WARNING
○ Be sure to attach the shoulder belt so that the grass
trimmer can be carried correctly.
○ If you get the feeling the tool is not operating normally,
turn off the motor immediately, remove the quick-release
bracket of the shoulder belt and remove the tool.
CAUTION
○ If you do not support the tool when you pull the quick-
release belt, it may fall causing injury or damage.
Hold the main pipe with one hand while you pull with the
other hand.
○ Make sure the quick-release function operates normally
before you start working.
(1) Place the shoulder belt on the shoulder as shown in
Fig. 12 (For use outside of Europe, see Fig. 14) and
engage it with the hanger on the tool. Adjust the shoulder
belt to suitable length.
(2) To remove the tool from the shoulder belt, support the
tool by holding the main pipe with one hand and use
the other hand to pull the quick-release belt as shown in
Fig. 12 (For use outside of Europe, see Fig. 14) to free it
from the bracket.
(3) To strap on the tool, insert the bracket in the hook and
insert the quick-release bracket over the hook and into
the wide opening of the bracket. (Fig. 13) (For use
outside of Europe, see Fig. 15)
Gently pull the shoulder belt to make sure that it is
properly attached.

NYLON HEAD

Installation of semi-auto nylon head
1. Function
Automatically feeds more nylon cutting line when it is
tapped.
Specifi cations
Type of
Code No. attaching
screw
Female
335234
screw
Applicable nylon cord
Cord diameter: Fig. 17
Length: 4 m
CAUTION
○ The case must be securely attached to the cover.
○ Check the cover, case and other components for cracks
or other damage.
○ Check the case and button for wear.
If the wear limit mark on the case is no longer visible or
there is a hole in the bottom of the button, change the
new parts immediately. (Fig. 20)
○ The nylon head must be securely mounted to the
threaded fastener of the motor case.
○ For outstanding performance and reliability, always
use HiKOKI nylon cutting line. Never use wire or other
materials that could become a dangerous projectile.
○ If the nylon head does not feed cutting line properly,
check that the nylon line and all components are
properly installed. Contact your HiKOKI dealer if you
need assistance.
2. Installation (Fig. 16 and 18)
(1) Insert the fl ange assy into the motor case. At this time,
the wing of the fl ange assy should face the motor case
side. Next, align the holes of the fl ange assy and the
motor case, insert the hex. bar wrench 4 mm, and then
turn to tighten the fl ange assy.
(2) Screw the nylon head directly to the threaded fastener of
the motor case.
The mounting nut of nylon head is left-hand-threaded.
Turn clockwise to loosen/ counterclockwise to tighten.
CAUTION
Install the nylon head properly and securely as instructed
in the handling instructions.
If not attached properly or securely, it may come off and
cause injury.
3. Adjustment of line length
Rotate and tap the nylon head on the ground. Nylon line
is drawn out abt, 30 mm by one tapping. (Fig. 19)
Also, you can extend nylon line with hands. This time the
motor must be completely stopped.
Confi rm the line extends in 30 mm increments by
"tapping" and "releasing" the bottom button while pulling
the line ends of the nylon head. (Fig. 20)
○ Appropriate Length of Nylon Line
The appropriate length of the line when the tool is in use
is 90 – 110 mm. Extend the line to the appropriate length.
4. Nylon line replacement
(1) Prepare 4m of genuine nylon line in Fig. 17. (Code No.
335235)
(2) Press the opposing tabs, and then remove the cover
from the case. (Fig. 21)
(3) Remove the reel from the case. (Fig. 22)
○ If there is nylon line remaining, hook the line in the
groves, and then remove the reel.
○ If the nylon line does not extend when there is enough
nylon line remaining, or when replacing the nylon
line (Code No. 335235), wind the nylon line using the
following procedure.
15
English
Size of
Direction of rotation attaching
screw
M10×
Counterclockwise
P1.25-LH