Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Ampere Rating
Volts
120
240
More Than
Not More Than
0
6
6
10
10
12
12
16
Grounding Instructions
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor
with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood,
or if in doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the tool's
plug.
Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than 150 volts:
This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A. The tool
has a grounding plug that looks like the plug illustrated in Sketch A. A temporary adapter, which looks like the
adapter illustrated in Sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in
Sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician. (This adapter is not permitted in Canada) The green-
colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box.
Fig 1
GROUNDING PIN
ADAPTOR
GROUNDING MEANS
Router Table Safety
WARNING: ALWAYS wear personal protective equipment;
• Hearing protection to reduce the risk of induced hearing loss
• Respiratory protection to reduce the risk of inhalation of harmful dust
• Cut-proof no-fray gloves to avoid possible injuries when handling router cutters and rough material due to sharp
edges. Any gloves where fabric material can work loose with the possibility of fabric strands MUST not be used
when operating the router table
• Safety glasses to avoid eye injury caused by flying particles
Ensure all people in the vicinity of the work area use adequate protection. Keep bystanders a safe distance away.
WARNING: ALWAYS connect the dust extraction port on the router cutter guard to a suitable vacuum
dust extraction system. Certain types of wood are toxic or may cause allergic reactions in people and animals,
especially when exposed to very fine dust. ALWAYS wear appropriate respiratory protection in addition to vacuum dust
extraction.
a) ONLY fit plunge routers that are listed as compatible in 'Specification' to the Router Table. Only fit router bits
that are suitable for the installed plunge router, with shanks compatible with the collet installed.
b) NEVER reach to the underside of the router table when the router is connected to the power supply.
c) ALWAYS remove the router plunge spring and plastic base plate, before fitting the tool to the router table.
This enables easy router bit change and height winder adjustment from above the table.
d) Keep your hands away from the cutting area. NEVER pass your hands directly over, or in front of, the revolving
cutter. As one hand approaches the router bit, move it AWAY from the cutter, in an arc motion over the top of the
router bit, to the out-feed side beyond the cutter. NEVER trail your fingers behind the workpiece and DO NOT use
awkward hand positions. Use push sticks and blocks where necessary.
e) Do not attempt to perform tasks on workpieces shorter than 300mm (12") in length without using special
fixtures or jigs. It is recommended to make work pieces oversize then cut to finished length.
f) ASSESS risks, benefits and alternatives BEFORE using push sticks, push blocks or other jigs and safety
devices. In many applications the use of such contraptions is useful and safe, however, in others it can be
dangerous. Push sticks can fly out of the operator's hand, when they come into contact with the revolving router
bit, potentially causing serious injuries.
g) ALWAYS support large workpieces on the in-feed and out-feed sides of the router table, and where
necessary, also to the sides. Use Triton Sliding Extension or Multi-stand wherever possible.
h) ALWAYS use guards, fences, horizontal and vertical featherboards etc., to guide the workpiece, counteract
and avoid kickback, especially when routing small or narrow workpieces. Vertical featherboards attached to
the fence also help prevent uncontrolled lift-up of the workpiece.
i) ALWAYS remove ALL loose objects from the table before operating. Vibrations may cause loose objects to
move, and come into contact with the cutter.
Table A
Total length of cord in feet
25
50
100
50
100
200
Minimum gage for cord
18
16
16
18
16
14
16
16
14
14
12
Not Recommended
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
j) NEVER attempt to remove wood fragments or dust from the cutter with your hands, whilst the router bit is
spinning. ALWAYS switch the router off, disconnect the machine from the power supply, and wait until the cutter
has come to a standstill. ALWAYS use cut-proof gloves when touching the cutter, to avoid injury.
k) ALWAYS inspect the workpiece for nails, staples and other metal objects and foreign bodies. If the router
150
cutter hits a concealed nail, the bit may be destroyed, high-velocity projectiles may be produced, kickback can
occur, all of which can lead to serious injury.
300
l) WHEREVER possible, use blind cutting techniques, where the router bit does not protrude from underneath
the workpiece. Keeping the cutter on the underside of the workpiece provides additional operator protection.
m) ONLY expose the smallest possible part of the cutter above the table surface. Keep any unused portion of the
14
cutter below the table surface.
12
n) ALWAYS test any new setup by rotating the spindle by hand, with the machine disconnected from the
power supply. Ensure proper cutter clearance to the throat place, fence and guard, before starting the machine.
12
o) ALWAYS use suitable throat plates, providing optimum clearance around the router bit.
p) ALWAYS use the router cutter guard, and adjust the guard to cover as much of the router bit as possible, as
close to the workpiece as possible. This not only protects the user from accessing the revolving router cutter, it also
provides effective dust extraction
q) LIMIT the depth of cut; NEVER remove too much material in one pass. Several passes with at smaller cutting
depth are safer, and produce a better surface finish.
r) ENSURE to adjust the router cutter speed, according to router cutter diameter and material being cut.
Use the speed selection dial on the plunge router.
s) ALWAYS feed AGAINST the rotation of the cutter. Both feed direction and rotation are indicated by arrows on the
router table surface.
t) ALWAYS use the fence if using a cutter without bearing or pilot. ALWAYS support the workpiece firmly against
the fence. NEVER remove the retractable guards on the fence. ALWAYS use a cutter with bearing or pilot for
freehand work.
Additional safety information
• ONLY use router cutters in perfect working condition compatible with the specification of the router table and
which are suitable for hand feeding operation (marked 'MAN' for manual operation according to EN 847-1)
• The bit must not enter the workpiece in the same direction as the feed direction. If this occurs, it is likely to cause
climb cutting, causing the workpiece to climb and pull away from the operator. This can lead to a loss of control
and a potential hazard during operation
• Do not attempt to re-sharpen router cutters unless you specifically follow the manufacturer's instructions and have
the equipment to complete this task. The majority of router cutters have blades that cannot be re-sharpened and
must be replaced immediately if dull
• Do not create fence traps caused by improper fence location. Fence traps happen when the fence is positioned so
far back that the front side of the workpiece would be behind the router cutter. These are dangerous due to the risk
of climb cutting and the difficulty of keeping the workpiece against the fence
• Ensure the correct table insert (table ring) is fitted that is the correct size for the size of the router cutter fitted
• Never use a router table until fully assembled and always re-check fasteners after re-assembly after storage
• Make certain the router is not plugged into the power outlet when installing into the table or when making
adjustments or changing accessories
• DO NOT plug the router into a standard mains wall socket. It must be plugged into the router table switch box so it
can be switched off in an emergency
• The router table must be installed on a solid level surface and secured so the table will not tip. Use of auxiliary
in-feed and out-feed supports is necessary for long or wide workpieces. Long workpieces without adequate
support could cause the table to tip towards the operator causing injury
• Routers create a lot of vibration and can work loose from their mountings. Check the mountings frequently and
re-tighten if necessary
• Never start the tool with the router cutter already engaged in the workpiece. This can lead to a lack of control and
possible injury
• The router table is designed to cut flat, straight and squared material only. Do not cut material that is warped,
uneven, weak or made from inconsistent material. If necessary make sure material is correctly prepared before
use. Incorrect material can lead to a lack of control and possible injury
WARNING: Unmaintained tools can cause uncontrolled situations. ONLY use router cutters that are correctly
sharpened, maintained and adjusted in accordance with the manufacturer's instructions.
Note: Seek professional training and assistance before attempting work that require procedures you are not familiar
with. STOP using the router table, if, at any point during operation, you encounter difficulties or are uncertain how to
proceed safely.
Product Familiarisation
1. Horizontal Featherboard T-Slot
2. Fence Face Spacer
3. Module Levelling Screw
4. Fence Micro-Adjuster
5. Vertical Featherboard
6. Guard Knob
7. Extraction Connector
8. Fence
9. Fence Knob
10. Table Scale
11. Module Levelling Screw
12. Thumb Hole
13. Featherboard Adjuster Knob
14. Fence Face
15. Module Mounting Rollers & Tracks
16. Cutter Height Winder Slot
17. Guard
18. Direction Indicator
19. Horizontal Featherboard
20. Featherboard T-Slot Knob
21. Featherboard Adjuster Knob
22. Module Levelling Bobbin Screw
23. Fence Face Adjustment Knob
24. Micro-Adjuster
25. Fence Slot
26. Fence Micro-Adjuster Knob
27. Table Scale Indicator
Intended Use
An effective router table capable of edge rebating, trenching, cross trenching, planing, edge moulding (fence and free
hand), end grain work, using a template guide, and morticing. For use with the Triton Workcentre TWX7 and Triton
Routers.
GB
3
Publicidad
Tabla de contenido
Solución de problemas
