Steinbach Speedclean 75/50 Manual De Instrucciones página 8

EN
This is the case when:
 The device has visible damage
 The device no longer appears funcional
 After long periods of storage in poor
conditions
If the power cord or other parts of this equip-
ment are damaged, they have to be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid
danger.
Damage during delivery
Your filter system has been carefully and professionally packed for
delivery. Please check to ensure that the package is undamaged
and that all parts are in the box. If you purchased this product on or-
der and the product was shipped to you, ensure that delivery is
complete. Damage to product as a result of shipping is not the re-
sponsibility of the supplier and must be immediately reported to the
shipper. The shipper assumes the liability for damages during deliv-
ery, the supplier is not responsible for it.
Implied Warranty
The manufacturer warranties safe operation and reliability only under
the following conditions:
 The filter system is installed and operated according to the
assembly and operating instructions.
 Only original replacement parts are used (consumable
parts do not fall under the warranty).
Expendable parts do not fall under the warranty. These include:
 All O-rings
 Pressure gauge
 Mechanical seal, complete
Resultant Damages
We cannot be responsible for damages to the product if the product
is not used in accordance with the instructions provided.
Technical Data:
Speedclean Comfort
Flow Volume (Q) 6,6 m³/h – 0,4 bar
MAX Operating Pressure
Filtration Area
Page 8 of 64
Speedclean
50 Comfort 75
8 m³/h – 0,4
bar
1,5 bar 1,5 bar
0,13 m² 0,13 m²
Rated Voltage 230V 1N~ AC 50Hz
Power
Protection Class
Max. ambient temperature
Sand Volume
Unpacking your filter system
Carefully remove the product and all component parts from the box.
Cross reference all parts in the box with the parts list reference chart
to make certain all parts are present before beginning assembly.
NOTE: Some parts may be located within the filter tank. To access
these parts you must remove the tank cover.
Refer to Appendix A for a complete EXPLODED VIEW PARTS
DIAGRAM
Power source Instructions
The filter pump system you have purchase is
equipped with a standard electrical cord and
plug which should only be connected to a
power outlet protected by a qualified Ground
–Fault-Circuit-Interrupter (GFCI) with I
30mA that has been installed by a profes-
sional electrician and adheres to local codes
and regulations. Electrical installations should
be carried out, taking the safety zone into
consideration, by a locally licensed electrician
to the relevant national specifications for
swimming pool construction (in Austria, EN1,
part 4, §49; in Germany, DIN 57100, Part 702
and VDE 0100, Part 702). To avoid electric
shock, power cord extensions should not be
used.
Filter- Pump Assembly (Picture 1 – 5)
1. Water Pump – Base Plate Assembly
a) Secure water pump to the base plate
mounting hardware. Orient as
2. Pump Fittings Assembly
a) Screw the 1¼"-1½" hose connector
water pump. Ensure that the O-ring "A" is installed between the
port and the connector.
b) Remove the threaded ring (Collar) on
pump.
c) Place O-ring "B" in the grove around the hair and lint strainer bas-
ket.
d) Place the transparent hair & lint strainer cover
screw the threaded ring (Collar) back on securely over the cover.
e) Insert O-ring "C" (1 1/4") inside the outward facing opening of the
transparent hair & lint strainer cover.
Sandfilter Speedclean 75/50 | 2015_V1
230V 1N~ AC
50Hz
450 Watt 550 Watt
IP X5 IP X5
35 °C 35 °C
15 kg 25 kg
ΔN
with the provided pump
shown.
into the center port of the
the outer opening of the
in place and then
≤