Replacement Parts - Omega Lift Equipment 44700 Manual De Usuario

WARNING
!
• Study, understand, and follow all instructions
provided before use.
• Do not exceed rated capacity.
• Do not exceed maximum width.
• Never crawl under the suspended load for
any reason.
• Ensure that the engine is supported securely
before repairing.
• Do not use this device for any purpose other than
that for which it is intended.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
OPERATIOn
1. Determine the location of the two engine support
bolts on your vehicle. Then place the Engine
transverse bar directly over these two bolts.
2. Adjust the boom extension (#2) to ensure that both
legs (#13 & 14) are sitting inside the fender of the
engine compartment.
If the inside fender lips are more than 61" apart,
!
the Engine Transverse Bar must not be used. Do
not exceed the designated marking (61"). Over-extending
could cause the Engine Support Bar to collapse, resulting
in personal injury or property damage.
3. Adjust to ensure the support arm (#10) is in correct
position. The rubber tip of the adjustable leg (#6)
should be on a flat, reinforced surface capable of
supporting the weight of engine. Tighten both wing
nuts (#4 & 8) to secure the adjustable leg (#6) and
support arm (#10).
4. Lower the threaded hooks (#3) to appropriate
position. Ensure that the hooks are directly over
the engine support bolts or brackets; therefore the
engine does not swing when vehicle is disassembled.
5. Attach the looped ends of the two 1/8" braided
steel cables (#12) to the engine support bolts on
the engine and loop middle of braided cables over
hooks. If the engine being supported is equipped with
engine lift brackets, hook the hooks (#3) directly into
engine lift brackets for extra protection.
note: Use only fasteners rated Grade 5 or higher as
engine support bolts.
6. Tighten the barrel hex. nuts (#7) on both hooks until
cables are snug or hex. nuts are tight against support
bar.
7. Double check that engine is properly supported
before disassemble the vehicle.
MAInTEnAnCE
Periodically inspect the Engine Transverse Bar. Ensure
all parts move freely. To help prevent rust, wipe clean
and/or blow dry after each use. If rust appears, sand
affected area and cover with suitable utility paint. Store
the Engine Transverse Bar in a clean, dry area.

REPLACEMEnT PARTS

(Refer to Figure 2 & 3)
Not all components of the Engine Transverse Bar are
replacement items, but are illustrated as a convenient
reference of location and position in the assembly
sequence. When ordering parts, give part number
and description. Call or write for current pricing: SFA
Companies 10939 N. Pomona Ave. Kansas City,
MO 64153, U.S.A. E-Mail: sales@omegalift.com
Tel: (888)332-6419 Fax: (816)891-6599
Omega Website: http://www.omegalift.com
Parts List
Item Part No.
1 -
2 -
3 *
4 *
5 *
6 44700-6
7 *
8 *
9 *
10 -
11 44700-11
12 44700-12
13 44700-17
14 44700-14
(*) 44700-15
- 44700-M0
- 44700-L0
(*) Hardware Kit includes item# 3, 4, 5, 7, 8 & 9
4
Description
Boom
Boom Extension
Threaded Hook
Wing Nut, M12
Hex. Bolt M12x120
Adjustable Leg
Barrel Hex. Nut
Wing Nut, M8
Hex. Bolt M8x65
Support Arm
Transfer Adapter
Braided Steel Cable, 1/8"
Leg, Boom
Leg, Boom Extension
Hardware Kit
Manual
Label for 44700
Qty
1
1
2
1
1
1
2
1
1
1
1
2
1
1
-
-
-