Hitachi CR 24DV Instrucciones De Manejo página 8

English
c) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
d) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause burns or a fire.
e) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
PRECAUTIONS ON USING CORDLESS
RECIPROCATING SAW
1. Always charge the battery at a temperature of 0–
40°C. A lower temperature than these specified
ranges will result in overcharging which will shorten
the battery life. The battery cannot be charged at
a temperature higher than 40°C. The most suitable
temperature for charging is that of 20–25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
SPECIFICATIONS
POWER TOOL
Model
No-Load Speed
Stroke
Capacity
Rechargeable battery
Weight
CHARGER
Model
Charging voltage
Weight
7
EB2420 (2.0 Ah)
EB2430HA (3.0 Ah)
UC24YFB
24 V
0.6 kg
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery. Short-
chircuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
6. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
7. When using this unit continuously, the unit may
overheat, leading to damage in the motor and
switch. Please leave it without using it for
approximately 15 minutes.
8. Do not insert object into the air ventilation slots
of the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
9. Using an exhausted battery will damage the charger.
10. Prior to cutting into walls, ceillings or floors, ensure
there are no electric cables or conduits inside.
11. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
12. During the cutting operation by reciprocating saw,
we recommend you to wear dust mask for your
health.
13. Wear earplugs to protect your ears during
operation.
14. Do not touch the blade during or immediately
after operation. The blade becomes very hot during
operation and could cause serious burns.
15. Always hold the body handle and front cover of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
16. Remove the battery from tool or place the switch
in the locked or off position before making any
adjustments, changing accessories, or storing the
tools.
CR24DV
0 – 2500 min -
28 mm
Mild Steel Pipe:
Vinyl Chloride Pipe:
Wood:
Mild Steel Plate:
Ni-Cd battery, 24 V
Ni-MH battery, 24 V
4.3 kg
1
(/min)
O.D. 100 mm
O.D. 100 mm
Depth 100 mm
Thickness 10 mm