Technical Data; Noise/Vibration Information; Fitting Protective Equipment - BTI WKS 17-125X RE X-LOCK Instrucciones De Servicio

(12) X-LOCK fibre disc A)
(13) X-LOCK clip for fibre discs
(14) Hand guard A)
(15) X-LOCK cup brush/disc brush
(16) X-LOCK holder
(17) Handle (insulated gripping surface)
(18) Extraction guard for cutting with a guide
A)
block
(19) Diamond cutting disc
(20) X-LOCK diamond core cutter
A) Accessories shown or described are not included
with the product as standard. Accessories can be
found in the BTI accessory range.

Technical data

English
Angle grinder
Article number
Rated power input
Power output
Rated speed
Speed adjustment range
Max. grinding disc dia-
meter
Speed preselection
Restart protection
Constant electronic control
Starting current limitation
Kickback stop
Weight according to EPTA-Procedure 01:2014
– with additional low-vibra-
tion auxiliary handle
– with standard auxiliary
handle
Protection class
The specifications apply to a rated voltage [U] of 230 V.
These specifications may vary at different voltages and in
country-specific models.

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted noise level of the power
tool is: Sound pressure level 92 dB(A); sound
power level 103 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and un-
h
certainty K determined according to
EN 60745-2-3:
42 | English
A)
A)
A)
A)
WKS
17-125X RE
X-LOCK
9 094 772
W 1700
W 1010
min -1 11500
-1
min 2800 –
11500
mm 125
●
●
●
●
●
kg 2.5
kg 2.4
/ II
English
Surface grinding (roughing):
2 2
a = 6.0 m/s , K = 1.5 m/s
h
Grinding with abrasive disc:
2 2
a = 4.0 m/s , K = 1.5 m/s
h
The vibration level given in these instructions has
been measured in accordance with a standard-
ised measuring procedure and may be used to
compare power tools. It can also be used for a
preliminary estimation of exposure to vibration.
The stated vibration level applies to the main ap-
plications of the power tool. However, if the power
tool is used for different applications, with differ-
ent application tools or poorly maintained, the vi-
bration level may differ. This can significantly in-
crease the exposure to vibration over the total
working period.
To estimate the exposure to vibration accurately,
the times when the tool is switched off or when it
is running but not actually being used should also
be taken into account. This can significantly re-
duce the exposure to vibration over the total work-
ing period.
Implement additional safety measures to protect
the operator from the effects of vibration, such as
servicing the power tool and application tools,
keeping the hands warm, and organising work-
flows correctly.
Fitting
English

Fitting protective equipment

Pull the plug out of the socket before carry-
u
ing out any work on the power tool.
Note: If the grinding disc breaks during operation
or the holding fixtures on the protective guard/
power tool become damaged, the power tool
must be sent to an after-sales service agent for
maintenance.
Protective guard for grinding
power tool and rotate the protective guard until it
audibly clicks into place.
Adjust the position of the protective guard (7) to
,
.
English
English
Place the protective
guard (7) onto the
holder on the power
tool until the coding
cams of the protective
guard are aligned with
the holder. When do-
ing so, press and hold
the unlocking lever (1).
Press the protective
guard (7) onto the
spindle collar until the
shoulder of the pro-
tective guard is sitting
on the flange of the
1 609 92A 4ZW • 5.4.19