Supplied Accessories; Control Guide - Panasonic SB-ZT2 Instrucciones De Funcionamiento

Front speaker
Setup example
(left)
Connected equipment
Surround
Main unit
speaker
(left)
Approx.120°
• Place the surround speakers slightly at the back right and left of the listening-viewing position.
• Aim the front face (with Panasonic logo) of each speaker at the
listening-viewing position for setting.

Supplied accessories

Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking for replacement parts.
(Product numbers correct as of February 2010. These may be subject to change.)
Supplied accessories differ depending on the symbols
(E, GN, GS) indicated on the packaging box.
Use correct accessories according to the region for use.
2 AC mains leads
For E
(For the United Kingdom and Republic of Ireland)
(K2CZ3YY00005)
For GN
(For Australia and New Zealand)
(K2CJ2DA00010)
For GS
(For Saudi Arabia, Kuwait,
Malaysia and Hong Kong)
(K2CZ3YY00005)
(220 to 240 V)
(For Thailand)
(K2CP2CA00001)
Leg cushion (1 sheet: 8 pieces) (RFA3045-2)
Keep the leg cushion out of reach of children to prevent swallowing.
Refer to page 3 for Sales and Support Information (for the United Kingdom and
Republic of lreland).
AC mains lead connection
FOR THE UNITED KINGDOM, REPUBLIC OF IRELAND, SAUDI
ARABIA, KUWAIT, MALAYSIA AND HONG KONG ONLY
READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 3
BEFORE CONNECTION.
To save power when the system is not to be used for a long time,
unplug it from the household mains socket.
Make sure to turn this system off before unplugging the AC mains lead.
For power consumption of speakers in standby, see page 5.
Power supply differ depending on the symbols (E, GN, GS) indicated on the packaging box.
Household mains socket
For E, GN
(AC 220 to 240 V, 50 Hz)
For GS
(AC 110 to 240 V, 50/60 Hz) AC mains lead
Note
The supplied AC mains leads are for use with this system only. Do not use them
with other equipment. Also, do not use AC mains lead for other equipment with
this system.
4
4
Front speaker
(right)
Surround
speaker (right)
(For continental Europe)
(K2CQ2CA00007)
(For Saudi Arabia)
(K2CA2CA00031)
(110 to 127 V)
(For others)
(K2CQ2CA00007)
Side view
AC IN
(supplied)
Installation
There is no positional distinction for each speaker before setting.
Make sure to place the speakers on a flat, stable surface so
there is no danger of them falling over.
When carrying speakers, hold the pole and base parts. (➜ below)
The speakers of this system are not magnetically shielded. Do
not install this system near a CRT-based television.
Note
• Make sure the base parts are not covered by cloth such as a curtain.
• Before attaching the leg cushion (included) on the base parts to
prevent tilt or rattle on the floor, make sure there are no people in
the surrounding area.
• Set the distance from each speaker to the listening-viewing position.
(➜ page 24 of SC-ZT2 Operating Instructions)
Wireless functions
As this system uses a frequency band of 2.4 GHz, the radio waves
may be interrupted by an obstacle. Depending on the surrounding
environment (i.e. radio wave interruption from outside, etc.) or the
building structure where this system is used (i.e. wall that easily
reflects radio waves, etc.), sounds may be cut or noise may occur.
Install this system properly paying attention to the following descriptions.
Equipment certification
As this system received Technical Conditions compliance certifi cation
based on the Radio Law, the wireless station license is not required.
However, if you do the following actions to this system, you may be
punished by law.
• Disassemble or refurbish
Restrictions for use
• Domestic use only.
• Use this system in the same room.
Do not place an obstacle between the main unit (SC-ZT2) and
speakers. Do not put things on the main unit.
Radio waves from this system reach maximum range of 15 m in the
same room. If there is an obstacle between the main unit (SC-ZT2) and
speakers or the main unit (SC-ZT2) is placed at the height of 50 cm or
below from the floor, the radio waves reach smaller range.
Keep this system away from equipment that generates radio
wave interference.
If the following equipment is located near the system, install this
system away from such equipment.
• Bluetooth, OA devices, telephone, etc.: approx. 3 m or more
• Microwave oven, wireless LAN compatible devices: approx. 3 m
or more
This system is designed to automatically avoid radio wave interference
with such household equipment. If radio wave interference occurs, the
Wireless Link display (➜ page 16 of SC-ZT2 Operating Instructions)
may blink, the sounds from speakers may be interrupted or noise may
occur.
These phenomena occur when this system selects a proper
frequency. These are not malfunctions.
Keep this system away from metal objects that tend to reflect
radio waves.
If there are metal objects or furniture in the room where this system is
installed, radio waves tend to be reflected. Depending on the listening-
viewing position, sounds may be interrupted or noise may occur. These
symptoms may be remedied by slightly moving this system's position.
Note that radio waves tend to be reflected also when this system is
installed in rooms with a lot of activity.

Control guide

Speaker (with built-in amplifier)
Pole (mid-high part)
Side view
AC inlet (➜ left)
Base
[WIRELESS LINK] indicator (➜ right
(woofer
1
page)
part)
When the unit is connected to the AC mains
supply, this indicator lights red in standby mode
and lights green when the unit is turned on.
Unit on/off button (k I l ^) (➜ right page)
2
WIRELESS LINK
Use this button to turn the unit on and off.
1
l (off): The unit is in standby mode.
2
k (on): The unit is on.
The unit is still using a small amount of power in
the standby. Standby uses less power.
Note
TEST terminal: This is used to check the product operation status.
Only used in factory. Do not insert a foreign object.
ID switch: This is used to check the product operation status and not
used regularly.
TEST terminal
ID switch
TEST ID
AC IN