Alertas; Errores Anteriores Al Vuelo; Figura 6.1.1.1: Mando - Alertas De Calibración En Curso; Calibración - 3DR SOLO Manual Del Usuario

6

Alertas

Las siguientes alertas aparecen en el mando en caso de error anterior al vuelo o durante el vuelo. Siempre vigile las
alertas del mando y realice las acciones recomendadas.
6.1

Errores anteriores al vuelo

Antes de arrancar los motores, Solo realiza una serie de comprobaciones automáticas para asegurarse de que el
sistema está listo para volar.
6.1.1 Calibración
Los siguientes errores indican que hay una comprobación anterior al vuelo en curso: calibrando altitud, calibrando
Solo y calibrando brújula. Espere a que se borre el error antes de continuar.
PREARM SENSOR ERRORS
Altitude
Si no coloca a Solo en una superficie nivelada, recibirá la siguiente alerta para moverlo a una superficie nivelada
para el despegue.
Compass
Please calibrate compass using
the 3DR Solo app
Level
Please calibrate level
using the 3DR Solo app
Si Solo requiere calibración manual, los siguientes mensajes de alerta mostrarán las pantallas para la calibración de
la brújula y del nivel. Consulte la Sección 9.2 para conocer las instrucciones de calibración de la brújula y del nivel.
Sensor
Please try and restart Solo
En el caso de un error de calibración o del sensor durante el encendido, reinicie Solo para borrar las siguientes
Control stick
alertas.
Contact 3DR customer support
Unknown
ARMING ALERTS
Calibration
Please restart Solo
ARMING ALERTS
Calibrating
Calibration
Please restart Solo
Calibrating
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
calibrating
Calibrating
Please wait
Throttle
PREARM SENSOR ERRORS
Compass error
Figura 6.1.1.1: Mando - Alertas de calibración en curso
This flight mode requires low
User asked to use Solo app to calibrate.
throttle before starting motors
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
error
Calibrating
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
Altitude calibrating
restart, and will run a fresh check when connected to Solo.
Please wait
Uneven
Level error
User is asked to use Solo app to calibrate
Move Solo to a level surface
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
error
Controller auto-shutdown
Throttle

Figura 6.1.1.2: Mando - Alerta de superficie desnivelada

Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Compass error
This flight mode requires low
throttle before starting motors
Please calibrate compass using
the 3DR Solo app
Service
Sensor error screen
For sensor errors requiring user-initiated restart
Use 3DR Solo app to log a trouble
ticket with customer support
error
Uneven
Level error
Move Solo to a level surface
Please calibrate level
using the 3DR Solo app
Control sticl error
Persists until:
Figura 6.1.1.3: Mando - Alertas de recalibración requerida
Controller starts with stick values in range.
error
Service
Sensor error
Use 3DR Solo app to log a trouble
Please try and restart Solo
ticket with customer support
Battery unknown
Displayed if Artoo is powered on with a battery has an
ID resistor unknown to Artoo. (Not logged in current software version's index.)
HAPTIC: Strong feedback, 40 millisecond pulse
?
After Solo is disconnected, Artoo should display "waiting for Solo"
battery
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
ARMING ALERTS
Timeout: after 1 minute (?) (results in "sensor error" screen)
error
Altitude calibration Calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Solo
Altitude calibration
Please wait
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Compass error Calibrating
error
User is asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (system then continues sensor check)
User powers off controller, or Solo
compass
Controller auto-shutdown
Altitude calibration
Please wait
Note: Artoo will not assume the same error is present on
System self-calibrates altitude after altitude disparity
restart, and will run a fresh check when connected to Solo.
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Calibrating
Compass error
Solo
User asked to use Solo app to calibrate.
Please wait
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
too high
Controller auto-shutdown
Compass error
Note: Artoo will not assume the same error is present on
User is asked to use Solo app to calibrate.
restart, and will run a fresh check when connected to Solo.
Altitude calibration
Alert persists until:
System self-calibrates altitude after altitude disparity
Alert persists until: User completes calibration using the app (system then continues sensor check)
System self-calibrates (sys then continues sensor check) User powers off controller, or Solo
Throttle
compass
Level error
Timeout: after 1 minute (?) (results in "sensor error" screen)
Controller auto-shutdown
User is asked to use Solo app to calibrate
This flight mode requires low
Please wait
Note: Artoo will not assume the same error is present on
Alert persists until:
throttle before starting motors
restart, and will run a fresh check when connected to Solo.
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
PREARM SENSOR ERRORS
surface
Controller auto-shutdown
Compass error
Note: Artoo will not assume the same error is present on
User asked to use Solo app to calibrate.
restart, and will run a fresh check when connected to Solo.
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Alert persists until:
Powers off controller, or Solo
User completes calibration using the app (sys then continues sensor check)
too high
Uneven
Catch-All
Controller auto-shutdown
Powers off controller, or Solo
Altitude calibrating
Remaining rare but problematic APM errors
Note: Artoo will not assume the same error is present on
Controller auto-shutdown
Move Solo to a level surface
will be captured under a catch-all for
restart, and will run a fresh check when connected to Solo.
Please wait
logging trouble tickets
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
required
Level error
Level error User is asked to use Solo app to calibrate
User is asked to use Solo app to calibrate
Alert persists until:
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Powers off controller, or Solo
surface Service
Controller auto-shutdown
Compass error
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
Note: Artoo will not assume the same error is present on Use 3DR Solo app to log a trouble
restart, and will run a fresh check when connected to Solo.
Please calibrate compass using
restart, and will run a fresh check when connected to Solo.
ticket with customer support
the 3DR Solo app
Catch-All
Sensor error screen
For sensor errors requiring user-initiated restart
Remaining rare but problematic APM errors
will be captured under a catch-all for
logging trouble tickets
Level error
required
Please calibrate level
using the 3DR Solo app
Control sticl error
Persists until:
Controller starts with stick values in range.
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
error
Please restart Solo
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Solo
Please wait
Compass error
User is asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (system then continues sensor
User powers off controller, or Solo
compass
Controller auto-shutdown
Please wait
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor che
Powers off controller, or Solo
too high
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
User is asked to use Solo app to calibrate
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
Alert persists until:
User complete calibration using the app (sys then continues sensor chec
System self-calibrates (sys then continues sensor check)
Powers off controller, or Solo
Timeout: after 1 minute (?) (results in "sensor error" screen)
surface
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Catch-All
Compass error
User asked to use Solo app to calibrate.
Remaining rare but problematic APM errors
will be captured under a catch-all for
logging trouble tickets
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
required
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Sensor error screen
For sensor errors requiring user-initiated restart
32