Milwaukee PJ 710 Instrucciones De Uso página 2

Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Mains
connection
Use
ENGLISH
You are demanding and expect to purchase quality goods – quality offered by
Milwaukee.
We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely.
We are sure that buying an Electric Power Tool from Milwaukee was the right choice!
Nominal power . . . . . . . . . . . . . . . . . . . . .
No-load speed . . . . . . . . . . . . . . . . . . .
Groove depth max.
Groove width . . . . . . . . . . . . . . . . . . . . . . . . .
Swivelling range
Router diameter
Blade bore diameter
Spindle thread . . . . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Please pay attention to the safety instructions in the attached leaflet!
J Always use the protective shields on the machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Always disconnect the plug from the socket before carrying out any work on the
machine.
Only plug-in when machine is switched off.
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Only use professionally grinded router cutters.
J If possible, clamp the workpiece down. Lead the machine with both hands.
J Only use properly sharpened blades, otherwise increased cutting forces will shatter
the workpiece. Only use blades intended for manual tool advance.
J Do not stop the blade by hand after switching off.
J The base plate must not be clamped down while the blade is extended. Lowering
and raising the blade must be easy going.
J Always fit the suction nozzle or the by–pass nozzle before using the joiner.
J Dust that arises when working in wood or using the tool on industrial material can be
dangerous to health. In this case connect the tool to a suction device (e.g.
Milwaukee absorbtion system AS 3 W).
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 87 dB (A).
Sound power level = 100 dB (A).
Wear ear protectors! Measured values determined according to EN 50 144.
Typically the hand-arm vibration is below 2.5 m/s
Measured values determined according to EN 50 144.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
The joiner can be used for mortise joints in solid wood, plywood, chipboard, fibre
board, plexiglass, and artificial marble.
Do not use this product in another way as stated for normal use.
1
10000 min
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 0–90
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
710 W
-1
19 mm
4 mm
o
100 mm
22 mm
M 10
2,8 kg
2
.
PJ 710