Attaching The Additional Handle; Adjusting The Depth Stop; Switching On And Off - Metabo SBE 521 Instrucciones De Manejo

Use the additional handle supplied with the
tool. Loss of control can lead to injuries.
Hold the power tool by insulated gripping
surfaces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the
operator.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Beware of gas/water pipes and electric cables!
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or in case of a power cut.
Keep hands away from the rotating tool!
Remove chips and similar material only with the
machine at standstill.
Caution must be exercised when driving screws
into hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or a high reverse torque may build up.
The machine produces powerful forces when
seizing or catching the workpiece. Always hold the
machine firmly, adopt a steady stance and focus on
your work.
Secure small workpieces. For example, clamp in a
vice.
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory
diseases to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in conjunc-
tion with additives for wood conditioning (chromate,
wood preservative). Material containing asbestos
must only be treated by specialists.
- Where the use of a dust extraction device is
possible it shall be used.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
5 Overview
See page 3 (please unfold).
1 Chuck key (for geared chuck) *
2 Geared chuck *
3 Futuro Plus keyless chuck *
4 Depth stop *
5 Additional handle *
6 Direction switch *
7 Sliding switch for normal drilling/impact
drilling *
8 Lock button (continuous operation)
9 Trigger
10 Speed preselection wheel *
* depending on the features / model
6 Commissioning
Before plugging in, check to see that the
rated mains voltage and mains frequency,
as stated on the rating label, match with your
power supply.
SBE 561, SBE 550, SBE 521, BE 561:
Make sure the chuck clamps securely:
After drilling for the first time (clockwise), firmly
tighten the safety screw inside the chuck using
a screwdriver. Caution: left-handed thread!
(see Section 7.8)
6.1

Attaching the Additional Handle

(SBE 561, SBE 550, SBE 521, SB 561)
For safety reasons, always use the
additional handle supplied.
Open the clamping ring by turning the additional
handle (5) anticlockwise. Push the additional
handle onto the collar of the machine. Insert the
depth stop (4). Securely tighten the additional
handle at the angle required for the application.
7 Use
7.1

Adjusting the Depth Stop

(SBE 561, SBE 550, SBE 521, SB 561)
Loosen the additional handle (5). Set depth stop (4)
to the desired drilling depth and retighten addi-
tional handle.
7.2

Switching On and Off

To start the machine, press the trigger switch (9).
SBE 561, SBE 550, SBE 521, BE 561: Press in the
trigger switch to change the speed.
For continuous operation the trigger switch can be
locked using the lock button (8). To stop the
machine, press the trigger switch again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine
with both hands using the handles provided,
stand in a safe position and concentrate.
ENGLISH
ENG
11