SLV 138980 Manual De Instrucciones página 4

Operating Manual PART B
Short-circuit proof safety isolating transformer for the
TENSEO wire system
138980 ...81 ...82
138990 ...91 ...92
1002691 ...92 ...93
Read manual carefully and keep for further use!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning
or fire!
 Installation, mounting or works on the electrical connection may only
be carried out by an approved electrician.
 The product may not be modified or converted.
 Do not hang or fasten anything on the product, especially no
decoration.
 Do not cover the product - provide free air circulation.
 Do not direct the spots on the transformer.
 To prevent damages from condensed water the transformer needs to
be acclimatised to room temperature before operation.
 In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of
adjacent surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
 This product is not intended to be used by children. Ensure that
children do not suffer any harm e.g. by burns from hot surfaces or by
electrical shock.
Additional safety messages are indicated by this symbol:
FUNCTION OF THE TRANSFORMER
 The transformer is a short-circuit proof safety isolating transformer and
transforms the mains voltage of 230V to extra low voltage of 12V.
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be used with a voltage of 230V ~50Hz.
 only be installed according to safety class I (one).
 only be operated when firmly mounted on a stable, even and tilt-
fixed surface.
 only be operated on normally or not flammable surfaces.
 only be used in dry condition,
 not in damp or dirt-endangered rooms.
 not in areas of high air humidity.
 not be exposed to strong mechanical loads or to strong
contamination.
OPERATION
High currents with low-voltage installations! Check all electrical
connections once in a while for a secure fit.
 The transformer is equipped with a thermo switch, which disconnects
the mains. After eliminating the fault and a prolonged disconnection
from the mains the transformer is operable again.
 The transformer is equipped with a fuse on the primary side. The fuse
is exchangable after an overload. Note the specification of the fuse.
MAINTENANCE AND CARE
Care
Disconnect the product from the power supply and let it cool down,
before you clean the product.
 Clean the product on a regular basis using a slightly moistened, soft
and fluff-free cloth. Please also note additional supplied notes on
maintanance and care.
STORAGE AND DISPOSAL
Storage
 The product must be stored in a dry and clean environment. Do not
strain the product mechanically during storage.
After a damp or soiling storage the product may only be
installed after checking its condition by an approved electrician.
Disposal (European Union)
 Do not dispose the product with the regular household waste!
Products marked with this sign must be disposed according to the
directive (WEEE, 2012/19) on electrical and electronic devices at local
collection points for such devices!
INSTALLATION
(only by an approved electrician)
Preparing the low-voltage (12V) power supply: The transformer should
be used up to 80% of its capacity. The total watt power of the connected
luminaires must not exceed the power output of the transformer. The
distance between luminaires and transformer should be at least 20 cm.
Switch off the mains or respectively the connection lead before
doing any works!
.
High currents with low-voltage installations! Use only heat resistant
wires and clamps to avoid danger of fire. Check all electrical connections
for a secure fit.
Use only parts, which are supplied with the product or are described
as accessories!
Inspect the product for loose parts inside the housing. When there
are loose parts inside the housing and these are not explicitly described
the product may not be installed or operated.
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
Unpacking
 Carefully take the product out of the packaging removing any transport
safeguards.
 Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
 The product is solely suited for installation on the wall and ceiling.
Operate the product only on an even, stable and tilt-fixed
background.
Installation steps (read completely before installation)
 Assemble the product as shown in the figure.
 Electrical Connection
 Remove the protection sleeve from the connection clamp.
 The product must be able to be separated by an all pole
separation from the current supply.
 Equip the three wire ends with protective tubes.
 For electric connection attach the black or brown wire (live
conductor) of the connection lead with the clamp L and the blue
wire (neutral conductor) of the connection lead with the clamp
N. The green-yellow wire (protective conductor) of the
connection lead has to be tightly connected with the earth
clamp of the product.
 Cover the connection clamp with the protection sleeve.
 Connect the secondary line to the transformer. Ensure a safe electrical
contact.
Check if the product functions properly and is securely fixed!
© 20.11.2019 SLV GmbH, Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany, Tel. +49 (0)2451 4833-0. Made in China.