Inflating Tires - EINHELL TH-AC 200/30 OF Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

otherwise stated in the operating instruc-
tions, damaged guards and parts have to be
repaired or replaced by a customer service
workshop. Damaged switches have to be
replaced by a customer service workshop.
Never use an electric power tool with a switch
that cannot be turned on and off.
Important!
For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than tho-
se recommended in the operating instructions
or catalog may place your personal safety at
risk.
Leave all repairs to a qualified electrician
Repairs must be left strictly to qualified elec-
tricians or the user might suffer an accident.
Noise
Wear ear muffs when you use the compres-
sor.
Replacing the power cable
To prevent hazards, leave the replacement of
damaged power cables strictly to the manu-
facturer or a qualified electrician. There is a
risk of electric shock!

Inflating tires

Directly after inflating tires, check the pressu-
re with a suitable pressure gauge, for examp-
le at your filling station.
Roadworthy compressors for building
site operations
Make sure that all lines and fittings are suita-
ble for the maximum permissible operating
pressure of the compressor.
Place of installation
Set up the compressor on an even surface.
Safety instructions for working with com-
pressed air and blasting guns
The compressor pump and lines can become
very hot during operation. Touching these
parts will burn you.
The air which is sucked in by the compressor
must be kept free of impurities that could
cause fires or explosions in the compressor
pump.
When releasing the hose coupling, hold the
hose coupling piece with your hand. This way,
you can protect yourself against injury from
the rebounding hose.
Wear safety goggles when working with the
blow-out pistol. Foreign bodies or blown off
parts can easily cause injuries.
Anl_SA_TH_AC_200_30_OF_SPK8.indb 21
Anl_SA_TH_AC_200_30_OF_SPK8.indb 21
GB
Do not blow at people with the blow-out pistol
and do not clean clothes while being worn.
Risk of injury!
Safety information for paint spraying
Do not process any paints or solvents with a
flash point below 55° C. There is a risk of ex-
plosion!
Do not heat up paints or solvents. There is a
risk of explosion!
If hazardous liquids are processed, wear pro-
tective filter units (face guards). Also, adhere
to the safety information provided by the ma-
nufacturers of such liquids.
The details and designations of the Ordi-
nance on Hazardous Substances, which
are displayed on the outer packaging of the
processed material, must be observed. Ad-
ditional protective measures are to be under-
taken if necessary, particularly the wearing of
suitable clothing and masks.
Do not smoke during the spraying process
and/or in the work area. There is a risk of ex-
plosion! Paint vapors are easily combustible.
Never set up or operate the equipment in the
vicinity of a fire place, open lights or sparking
machines.
Do not store or eat food and drink in the work
area. Paint vapors are harmful to your health.
The work area must exceed 30 m
ent ventilation must be ensured during spray-
ing and drying. Do not spray against the wind.
Always adhere to the regulations of the local
police authority when spraying combustible or
hazardous materials.
Do not process media such as white spirit,
butyl alcohol and methylene chloride with the
PVC pressure hose. These media will destroy
the pressure hose.
Operating pressure vessels
You must keep your pressure vessel in good
working order, operate the vessel correctly,
monitor the vessel, carry out necessary main-
tenance and repair work immediately and
meet the relevant safety precautions.
The supervisory authority may enforce essen-
tial control measures in individual cases.
A pressure vessel is not allowed to be used if
it has faults or deficiencies that can endanger
workers or third parties.
Check the pressure vessel for signs of rust
and damage each time before using. Do not
use the compressor with a damaged or rusty
pressure vessel. If you discover any damage,
- 21 -
and suffici-
3
07.05.15 14:13
07.05.15 14:13

Publicidad

Tabla de contenido
loading

Tabla de contenido