Milwaukee M-SPECTOR Manual Del Operador página 2

GENERAL POWER TOOL
SAFETY WARNINGS
Read all safety warnings and all
WARNING
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. The term "power tool" in the warnings
refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Do not operate power tool in an area where it
could contact electrical wiring or an electrically
charged object. Contact with a "live" wire or
object will make exposed metal parts of the tool
"live" and shock the operator.
• Do not operate power tool near moving ma-
chinery. The cable can be tangled in moving parts,
pulling in the power tool and your hands and arms.
• Do not use near any heat sources such as ra-
diators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock. Dry hands before turning tool
on or off and before removing or installing the battery
pack.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
• This Inspection Scope is not intended for medi-
cal use or personal inspection.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tool
operation. Do not use if power tool smokes or
gives off fumes. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
• Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation. Only use accessories
specifically recommended for this tool. Others may
be hazardous.
• Clean only with dry cloth. Certain cleaning agents
and solvents are harmful to plastics and other
insulated parts. Some of these include: gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Clean dust and debris
from vents. Keep the apparatus handle clean, dry
and free of oil or grease.
BATTERY USE AND CARE
• This tool is designed to be powered by one (1)
9V battery properly inserted into the tool. Do
not attempt to use with any other voltage or power
supply.
•Do not leave battery within the reach of children.
• Install battery according to polarity (+ / –)
diagrams.
• Properly dispose of used batteries immediately.
• Do not incinerate or dismantle batteries.
• Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Contact a MILWAUKEE service facility for ALL
repairs. Have your power tool serviced by a
qualified repair person using only identical re-
placement parts. This will ensure that the safety
of the power tool is maintained.
• Never disassemble the power tool or try to do any
rewiring on the power tool's electrical system.
SPECIFIC SAFETY RULES FOR
INSPECTION SCOPE
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
SYMBOLOGY
Volts
Direct Current
To prevent electric shock, do not allow
product to contact live electrical parts
Federal Communications Commission
SPECIFICATIONS
Cat. No. ..................................................... 2309-20
Volts ..................................................9 DC (one 9V)
Cable Length ......................................................3 ft
2
SERVICE