Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
16
| English
10 Filter element (Microfilter System) (GSS 140 - 1A)
11 Vacuum hose*
12 Perforating tool*
Technical Data
Orbital sander
Article number
Rated power input
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via Velcro backing
— Attachment via clamping
Sanding plate dimensions
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Assembly
u Before any work on the machine itself, pull the mains
plug.
Replacing the Sanding Sheet
When attaching a new sanding sheet, remove any dust or
debris from the sanding plate 4 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Sanding Sheets without Velcro Backing (see figure A– C)
n Unlock both sanding-sheet clamps 5 and swivel them
downwards.
o Insert the sanding sheet 6 under the rear clamping
bracket 3. Ensure that the sanding sheet 6 is not too
short and that it is correctly clamped. Swivel the
sanding- sheet clamp 5 back into the starting position
and lock it there.
p Place the sanding paper taut around the sanding plate 4.
Clamp the front part of the sanding sheet under the front
clamping bracket 7. Ensure that the sanding sheet 6 is
not too short and that it is correctly clamped. Swivel the
sanding-sheet clamp 5 back into the starting position
and lock it there.
Sanding sheets without holes, e. g. from rolls or by the meter,
can be punctured with the perforating tool 12. For this, push
the power tool with the sanding sheet mounted onto the
perforating tool (see figure F).
To remove the sanding sheet 6, unlock both sanding-sheet
clamps 5 and pull the sanding sheet out of its holder.
Sanding Sheets with Velcro Backing
Sanding plates 4 fitted with Velcro backing can be used to
fasten sanding sheets with Velcro adhesion quickly and easily.
Before attaching the sanding sheet 6, free the Velcro backing
of the sanding plate 4 from any debris by tapping against it in
1 600 A00 3UF | 05.2014
Manual GSS 140-1 e 140-1A Professional.indd 16
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
GSS140 - 1
3 601 BA2 0..
W
180
-1
min
12000
-1
min
24000
m
m
1
115 x 107
mm
mm
115 x 140
mm
110 x 100
g k
1
order to enable optimum adhesion.
Position the sanding sheet 6 flush alongside one edge of the
sanding plate 4, then lay the sanding sheet onto the sanding
plate and press firmly.
To remove the sanding sheet 6, grasp it at one of the tips and
pull it off from the sanding plate 4.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
of material removal, different sanding sheets are available:
working of all wooden materials
For coarse-sanding, e. g. of rough, un-
planed beams and boards
For face sanding and planing small ir-
e r
u g
r a l
i t i
s e
For finish and fine sanding of hard
w
o o
s d
For the working of paint/enamel
coats or primers and fillers
For sanding off paint
For sanding primer
For final sanding of primers before
o c
i t a
g n
GSS140 -1A
3 601 BA2 1..
180
12000
24000
6 ,
1,6
115 x 107
115 x 140
110 x 100
3 ,
1,4
/II
/II
Grain size
40—240
For the
coarse
40, 60
m
d e
u i
m
8
0
1 ,
2
0
i f
e n
1
8
0
2 ,
4
0
40—240
coarse
40, 60
medium 80, 120
i f
e n
1
8
0
2 ,
4
0
Bosch Power Tools
30/06/14 09:45
Publicidad
Tabla de contenido
