Technical Data; Before Starting The Equipment - Toolson PRO-HB 82 Manual De Instrucciones Original

4. Technical data

Mains voltage: ................................ 230 V ~ 50 Hz
Power input: ............................................... 720 W
Idling speed: ..................................... 17000 min
Chip depth: .............................................. 0-2 mm
Rebate depth: .......................................... 0-8 mm
Plane width: .............................................. 82 mm
Protection class: ............................................ II/
Weight: .......................................................3.6 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 95 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 106 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
Anl_PRO_HB_82_SPK7.indb 16 Anl_PRO_HB_82_SPK7.indb 16
-1
= 5.6 m/s
2
h
2
- 16 -
GB
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Adjusting the chip depth (Fig. 4/Item 1)
You can adjust the chip depth in steps of 0.2 mm
from 0 to 2 mm by turning the setting knob for the
chip depth (1).
Turn the setting knob for the chip depth (1) in a
clockwise direction to set a greater chip depth.
Greater chip depth
Turn the setting knob for the chip depth (1) in a
counter-clockwise direction to set a lower chip
depth. Lower chip depth
After fi nishing work, set the chip depth so that the
knives are lowered and thus protected from da-
mage. Turn the setting knob for the chip depth to
position "P" for this purpose.
5.2 Chip extraction (Figure 5)
For optimum chip extraction you can connect the
supplied dust bag (2) to the hand-held electric
plane. To do so, slide the dust bag (2) into the
chip ejector (7) on the side of the hand-held elec-
18.05.15 10:10 18.05.15 10:10