Maintenance And Care - Kikkaride TRIPP Instrucciones De Uso

WARNING
PLEASE READ THIS INSTRUCTION CAREFULLY BEFORE USING THE SCOOTER AND SAVING IT FOR LATER USE !!!
• Before you allow your child to use TRIPP, ensure that the steering rod is fully engaged and that all the screws are tight. Also ensure that the wheels have been
correctly secured and that they show no signs of wear.
• Protective equipment should be worn. Ensure that your child always wears a helmet, and wrist, elbow and knee pads, as well as shoes with rubber soles.
• Ensure that your child does not ride down any steep hills. The brake is not designed to decelerate from high downhill speeds.
• The brake pad becomes hot when it is used. Make especially sure that your child does not keep the brake on for a long period of time. Explain to your child that
direct skin contact may cause burns.
• Do not allow your child to travel at speeds exceeding 5km/h.
• Ensure that your child does not ride on roads, paths or other places with motor vehicle traffic.
• Only one child may ride on the TRIPP at any one time.
• Never allow your child to ride the TRIPP scooter at dusk or at night.
• The TRIPP scooter must not be used on wet, oily, sandy, dirty, icy, rough or uneven surfaces.
• Your child should practice first go gain control of the vehicle. Ensure that your child does not attempt any experiments or risky maneuvers with it. Riding style
should always be adjusted to the personal skill of the rider.
• Do not make any modifications to the TRIPP.
• Suitable for children up to approx.120cm is height for the TRIPP and approx.
• Undoing the axle screws several times will reduce the effect of the screw securing products. This means that the screws may come loose by themselves. You
should therefore always use a conventional screw securing product.
• Some metal parts may corrode after a certain time, especially when used near the sea or left outdoors too often.
• The toy needs to be used with caution, since skill is required to avoid falls or collisions causing injury to the users or third parties.
• User age and maximum loading weight.
Scooter mode: 50kg.max and 3-5 years of age.
Seat mode: 20kg.max and 1+ years of age.
This scooter complies with: EN 71-1:2014; EN71-2:2011+A1:2014; EN 71-3:2013+A1:2014;
ASSEMBLY THE SCOOTER
Follow steps 1to 5
• Adult assembly required. Warning! Not to be used by children under 36 months due to small parts while unassembled. Choking Hazard.
• Press the button (F) and insert the stem into hole (H), please note that the slot (G) must sit over the raised rib (I) inside the hole, and make sure that (F) is fixed
with (J) correctly.
• If you have bought the seat for TRIPP, congratulations that the scooter can be used as 3 versions (Figure 6).
HOW TO MOUNT THE SEAT ONTO TRIPP (Figure 7).
MAINTENANCE AND CHECK BEFORE RIDING
• Check that all parts are su ciently tightened and the handlebar is securely xed.
• Check that all wheels can be swung smoothly and that the footplate is securely fastened.
• All nuts and bolts may lose their tightness over time, please check the tightness of all nuts and bolts every time you ride.
• The wheels may become worn out with natural wear and tear over time. Please check the condition of the wheels regularly and replace them when necessary.
Please contact the place of purchase for new wheels.
• DO NOT use a wet cloth, alcohol, industrial cleaners or solvents to clean the scooter as this may result in loss of gloss, the removal of decals or dissolve the
materials in the scooter.
• Do not attempt to make any modi cations to the scooter by yourself.

MAINTENANCE AND CARE

Fabric parts:
1. The fabrics must be cleaned with warm water and mild soap. After cleaning let get completely dry before you use it. If is absolutely forbidden to fold it and
store it before it is completely dry.
2. Do not use strong cleaning agents, bleach or agents with abrasive particles, in order to clean the product. It is forbidden to clean it in a washing machine,
dryer, dry cleaning, bleach and tumble-dry it.
Plastic and metal parts
1. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
2. Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the metal and plastic
parts and fading of the fabrics of the crib.
3. When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room temperatures.
From time to time check all plastic parts that are hanged on the frame. Tighten all screw and bolts if necessary.
ENGLISH