Tools Required - Teka UNIVERSE CUADRO 79.002.64 Instrucciones De Instalación

TOOLS REQUIRED

Power drill, ø 6mm masonry drill
bit, screwdriver, pencil.
BEFORE YOU START
The screws and wall plugs sup-
plied are only suitable for use on
solid walls. For hollow /plaster-
board walls, purchase appropriate
fixings.
Please ensure there are no hidden
service pipes or cables where you
intend to drill.
The working pressure of this prod-
uct is 0.5kgf/cm2 - 6.0kgf/cm2.
The recommended water pressure
is 2.0kgf/cm2 - 5.0kgf/cm2.
Please be careful of your safety
while drilling and installing.
This product has passed the func-
tionality test before leaving the
manufacturer.
INSTALLATION
1. Install the fixity1 and fixity2
1.1 Drill two Ø 6 mm holes in the
wall approximately 700 mm apart.
The depth of holes should be no
more than 35 mm. Insert the wall
plugs (1) into the holes.
1.2 Screw the fixity1 (2) and the
fixity2 (4) into the wall with the tap-
ping screws (3). Adjust the distance
between the fixities to be 700 mm.
Tighten them into the wall.
Note: Fixity1 and fixity2 are differ-
ent, so their positions are not inter-
changeable.
2. Assemble the shower bar
2.1 Unscrew the grub screw at the
end of the shower arm (6). Insert
the flange cover (5) onto the show-
er arm, then screw the grub screw
back into place.
2.2 According to the installation
sketch map, put the slider (10) onto
the bar (11) and then screw the bar
into the shower arm (6).
2.3 According to the installation
sketch map, unscrew the nut con-
nected to the ceramic shower arm
diverter (12) and separate the
washer from the nut. Put the nut
and the washer onto the bottom
end of the bar; then, one by one, in-
sert them onto the ceramic shower
arm diverter.
3. Install the shower bar
NIVERSE CUADRO INST.indd 5
3.1 Align the shower bar with the
fixiy1 and fixity2 and install it into
them. Tighten the grub screws
found at the end of ceramic shower
arm diverter and shower arm.
3.2 Tighten the nut at the bottom
of bar.
3.3 Install the shower head (7) onto
the shower arm.
3.4 Connect the swivel nut of the
short hose (13) to the underside
connector of the ceramic shower
arm diverter, and connect the other
end of the short hose to the shower
faucet connector.
4. Install the hand shower
4.1 According to the installation
sketch map, connect the long hose
(9) to the underside connector of
the ceramic shower arm diverter.
Connect the other end of the long
hose to the hand shower (8).
4.2 Press the slider button and ad-
just the height of the slider accord-
ing to your preference.
Check the installation step by step
to ensure stability and tightness
and to avoid any leaks before test-
ing the shower spray.
USE OF CERAMIC SHOWER ARM
DIVERTER
1. The ceramic shower arm diverter
controls the hand shower and the
shower head.
2. Turn the ceramic shower arm
diverter handle to the vertical po-
sition to direct water to the shower
head.
3. Turn the ceramic shower arm
diverter handle to the horizontal
position to direct water to the hand
shower.
4. Turn the ceramic shower arm
diverter handle to the position be-
tween 1 and 2 to direct water to
both the shower head and the hand
shower.
MAINTENANCE
Keep the slide rail clean. Clean
only with a mild non-abrasive de-
tergent and soft cloth.
GB
23/6/09 22:08:44