Honeywell HZ-340E Manual Del Usuario página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
USER'S MANUAL
HZ-340E Ceramic heater with rotary power
switch and thermostat
HZ-345E Ceramic heater with rotary power
switch, thermostat and oscillating function
1.
Make sure that the rotary power switch (3)
is in the OFF position (4). Insert the power
plug into the power socket. Do not touch
the power cable with wet hands.
2.
Make sure that the air intake vent (13) and
air exhaust vent (2) are not blocked. The
air intake vent (13) and air exhaust vent
must always remain free during the heating
operation.
3.
For the heating function use the rotary
power switch (3) and the rotary thermostat
switch (9) depending on the model and as
described below.
4.
Before moving or storing the ceramic
heater, or when you do not wish to use it,
turn the rotary power switch (3) to the OFF
position (4) and disconnect the power plug
from the power socket.
Rotary power switch
1.
By turning the rotary power switch (3) in a
clockwise direction, you can choose
between the following settings:
Position
O
OFF (4)
I
1000 W (5)
II
1500 W (6)
I
1000 W oscillating (7)
II
1500 W oscillating (8)
2.
When the rotary power switch (3) is on the
highest position II (6) or II
on the model, you cannot turn it further in a
clockwise direction, but only in an
anti-clockwise direction.
Rotary thermostat switch
1.
Turn the rotary thermostat switch (9) in a
clockwise direction to the highest position
„MAX" (11) . The operating control lamp
(12) lights up.
ENGLISH
HZ-340E HZ-345E
(3 Positions)
(5 Positions)
x
x
x
x
x
x
0
x
0
x
(8), depending
2.
When the desired room temperature has
been reached, turn the rotary thermostat
switch (9) in an anti-clockwise direction
until you hear a clicking sound. Now the
thermostat switches off the heating function.
The operating control light (12) goes off.
3.
Now turn the rotary thermostat switch (9)
back slightly in a clockwise direction. The
ceramic heater will now switch the heating
function on and off automatically to
maintain the chosen room temperature. The
operating control lamp (12) goes on an off
respectively.
4.
The further you turn the rotary thermostat
switch (9) in a clockwise direction, the
warmer the room temperature will be.
5.
When the rotary thermostat switch (9) is in
the highest position (11), you cannot turn it
in an anti-clockwise direction, but only in
an anti-clockwise direction.
6.
When the thermostat is set at the lowest
setting (10) and the rotary power switch (3)
is switched onto a heating setting, the
ceramic heater begins the heating
operation as soon as the room temperature
sinks to below about + 5 °C. The ceramic
heater continues the heating operation until
the room temperature rises above about
+ 5 °C.
Oscillating function
1.
Turn the rotary power switch (3) to position
I
(7) or II
the desired room temperature as described
under „rotary thermostat switch".
2.
During the heating operation the ceramic
heater oscillates and the operating control
lamp (12) lights up.
3.
When the heating operation is switched
off, the operating control lamp (12) goes
off and the oscillation stops.
Overheating protection
1.
The ceramic heater is equipped with
overheating protection, which switches the
ceramic heater off automatically if it
overheats.
2.
If this happens turn the rotary power switch
(3) to the OFF position (4) and disconnect
the power plug from the power socket.
5
(8) and set the thermostat to

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hz-345e

Tabla de contenido