Before Starting The Equipment; Operation; Important - EINHELL TC-PO 1100/2 E Manual De Instrucciones

Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Assembly (Fig. 4-6)
Important! Pull out the mains power plug before
starting the assembly work.
Anl_SA_TC_PO_1100_2_E_SPK8.indb 21 Anl_SA_TC_PO_1100_2_E_SPK8.indb 21
GB

6. Operation

Secure your workpiece. Make sure that the work-
piece is held securely by a clamping device or a
vise.
Switching the equipment ON/OFF
The equipment is turned on (I) and off (0) with
the ON/OFF switch (Fig. 3 / Item 3). However, the
equipment will only start running after the speed
control has been activated (see section 6.3).
6.1 Using as a polishing machine
When using waxing and polishing agents,
observe the instructions issued by their ma-
nufacturer!

IMPORTANT!

To prevent damage to the surfaces of the work-
pieces you wish to polish, make sure that you
observe the following instructions:
•
Make sure that the polishing attachment is
always mounted precisely in the center of the
sanding/grinding disk.
•
Before you start the equipment, check to
ensure that the attachments are securely ins-
talled.
•
Never touch the area you wish to polish with
the edge of the sanding/grinding disk.
•
Use the speed selector (Fig. 3/Item 4) to
select the following maximum speeds for poli-
shing:
- Working in polish: approx. 1000 rpm
- Polishing to a
high gloss: approx. 1000-1100 rpm
- Polishing up: approx. 1400 rpm
If you do not comply with these instructions, the
manufacturer cannot accept any liability.
The Velcro fastener enables easy changing of the
polishing attachment.
Use the foamed plastic attachment to apply
the polishing agent (Fig. 7).
•
Make sure that the foamed plastic attachment
is free of any foreign bodies.
•
Spread the polishing paste evenly over the
polishing pad. Do not apply the polish directly
to the polishing surface.
•
Switch the polishing machine on and off only
when the polishing machine is resting on the
polishing surface.
•
Place the extension lead over your shoulder
- 21 -
21.12.2017 08:47:19 21.12.2017 08:47:19