Virutex UCP90 Manual De Instrucciones página 4

VIRUTEX se reserva el derecho de modificar sus productos
sin previo aviso.
E N G L I S H
UCP90 GUIDE FOR
PARALLEL CUTTING
(Diagrams on page 13)
1. SAFETY INSTRUCTIONS FOR USING THE
UCP90 GUIDE FOR PARALLEL CUTTING
Before using the guide for parallel cu-
tting, carefully read this INSTRUCTION
MANUAL and the GENERAL SAFETY
INSTRUCTIONS.
Make sure you understand before
starting to operate the machine.
Keep the instruction manual for pos-
sible consultation later on.
Also read carefully the operating instructions for the
machine you are going to mount on the guide and follow
the safety measures indicated.
2. GENERAL DESCRIPTION
The UCP90 guide allows you to make parallel cuts with
circular saws, jigsaws and Virutex surface routers.
You can work with the SR90J circular saw, fitting it
directly on the UCP90 system.
To fit the SR74K circular saw on the guide rail of the
UCP90 you will need the support SR74K 90.45.767
(optional accessory).
To work with SC134L and SC234L jigsaws on the UCP90
system, you should use the optional accessory. Jigsaw
support 90.23.537.
Finally, to work with surface routers FR66P, FR160P,
FR277R or FR278R, you should use optional router
accessory 90.45.758.
3. UCP90 STANDARD SUPPLY
The box contains the following items:
A complete 1.40 m rail.
Two holding G-clamps.
Two UCP90 suction cups.
Operating instructions and miscellaneous documen-
tation
4. OPTIONAL ACCESSORIES
90.45.767 Support for circular saw SR74K.
90.23.537 Support for Jigsaws SC134L and SC234L.
4
90.45.758 Support for routers FR277R, FR278R, FR66P
and FR160P.
Other accessories:
90.45.754 Complete 1.40 m rail.
90.45.755 Complete 2.40 m rail.
60.45.756 UCP90 suction cups (set of two) 60.45.710
Set of 2 holding G-clamps
90.45.812 UCP90 rail jointing kit
5. RAIL PREPARATION
Insert the clamp guide rod (D, Fig. 1) in the indicated
hole on the rail (B, Fig. 1) from one end.
Insert the screws (E, Fig. 1) that fasten clamps F in the
guide rod slot (D, Fig. 1).
Fit the clamps (F, Fig. 1) in screws E, and fasten them
with the washers and wing nuts (G and H, Fig. 1). Insert
the screws (J, Fig. 1) in the clamp holes (F, Fig. 1) without
tightening them.
6. MOUNTING THE MACHINE ON THE RAIL
MOUNTING A SR90J CIRCULAR SAW
Place the saw in front of the guide rail (B, Fig. 2), insert
the fixing clamps (F, Fig. 2) in the rim of the machine
base and firmly fasten with the screws (J, Fig. 2).
The cutting line is 145 mm from the edge of the guide
rail (Fig. 2).
MOUNTING A SR74K CIRCULAR SAW
To fit the machine on the guide rail, optional acce-
ssory support 90.45.767 should be used for circular
saw SR74K.
Remove fixing clamps F from the guide rail, fit the support
for SR74K on its screws (E, Fig. 3) (S, Fig. 3) and fasten it
with the washers and wing nuts (G and H, Fig. 3).
Fit saw SR74K on the support (S, Fig. 3). Fasten the
machine to the support with the knob (D, Fig. 3) from
the front part and with the clamp (C, Fig. 4) from the
back.
The cutting line is 200 mm from the edge of the guide
rail (Fig. 3).
MOUNTING A SC134L OR SC234L JIG SAW
To fit these machines on the guide rail, optional acces-
sory support 90.23.537 is necessary for jigsaws SC134L
and SC234L.
Fit the jigsaw on the support (S, Fig. 5) and fasten it
with 2 M5 screws (T, Fig. 5). Position the support with
the saw mounted in front of the guide rail (B, Fig. 5),
insert the fixing clamps (F, Fig. 5) in the rim of the
support (S, Fig. 5) and firmly fasten it with the screws
(J, Fig. 5). The cutting line is 60 mm from the edge of
the guide rail (Fig. 5).
MOUNTING A FR277R, FR278R, FR66F, FR66P OR
FR160P ROUTER