Publicidad
Idiomas disponibles
Idiomas disponibles
Changing steps:
1)
Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2)
Select the required page via the PAGE button.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern
(flash buttons in the lower row of the section PRESET B).
5)
Select the required step via the STEP button.
6)
Now you can change the light intensity of the lamps as follows: hold the DOWN button pressed while pressing the
flash button of the channel that you want to change. The display shows which setting has been selected. (0 – 255
is equivalent to 0 – 100%)
7)
Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
MUSIC CONTROL
Connect an audio source to the RCA input at the rear side (100mV p-p). Switch the music control on via the AUDIO
button. The green LED lights up. Set the required effect via the slider control AUDIO LEVEL.
STORING A RUNNING LIGHT SPEED
1)
Switch the music control off.
2)
Select the required pattern via the PAGE button and the appropriate slider control of the section PRESET B.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Select the MIX CHASE mode via the PARK button (the yellow LED lights up)
5)
Set the running light speed via the SPEED slider control or press in the right rhythm twice the TAP SYNC button.
You can repeat this until you have found the correct speed.
6)
Store this speed setting in the memory by holding the REC SPEED button down while pressing the flash button of
the appropriate pattern. The slider control that triggers the pattern, must be in the upper position.
ERASING A PROGRAMMED SPEED
1)
Switch off the music control.
2)
Select the required pattern via the PAGE button and the appropriate slider control of the section PRESET B. Set
the slider control completely to the top.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Select the MIX CHASE mode via the PARK button (the yellow LED lights up).
5)
Push the slider control SPEED completely down.
6)
Hold the REC SPEED button down while pressing the flash button of the appropriate pattern. The fixed speed
setting is now erased.
CHANGING THE RANGE OF THE SPEED CONTROL
This slider control has two adjustable control ranges: 0.1 seconds to 5 minutes and 0.1 second to 10 minutes. Hold the
RECORD/SHIFT button down and press three times in sequence the flash button number 5 (from the top row) to set
the range to 5 minutes, or three times the flash button 10 for the 10 minutes setting. The selected range is indicated by
the yellow LEDs just above the SPEED control.
EXPLANATION OF SOME SPECIAL FUNCTIONS
Note: When the scene setter is switched on, the BLACK OUT function is automatically activated. All outputs are set to
zero so that the connected light effects do not work. Press the BLACK OUT button to leave this mode.
Fade time:
The FADE control sets the fading time between the different light positions.
Single Mode:
In single mode all running light programs will be played in sequence. Select the CHASE-SCENES mode via the MODE
SELECT button (red LED) and the SINGLE CHASE mode via the PARK button (yellow LED). Make sure that the audio
control is switched off. The SPEED control sets the speeds of all patterns.
Mix Mode:
Multiple play of the stored patterns. Select CHASE-SCENES via the MODE SELECT button (red LED) and MIX
CHASE via the PARK button (yellow LED). Make sure that the audio control is switched off and set the speed of the
light effects individually via the SPEED control.
Indications on the display:
The display shows the different settings and pattern numbers. You can choose between the display of the DMX value
(0 to 255) or a percentage (0 to 100%) of the light setting. Hold the RECORD/SHIFT button down while pressing the
INSERT/% or 0-255 button. Set one of the slider controls 1 to 24 in the upper position and check the display. If
required, repeat these steps.
The minutes and seconds are indicated on the display by two dots. E.g. 12 minutes and 16 seconds are displayed as
12.16.. If the time is below 1 minute, it is displayed by 1 dot e.g. 12.0 is 12 seconds and 5.00 is 5 seconds.
Blind function:
User manual DISCOVERY 12/24 Triton Blue | Rev. Sep 2013 | www.triton-‐blue.com
Publicidad
