Publicidad
Idiomas disponibles
Idiomas disponibles
1)
Activate the programming mode as described in the Basic Functions.
2)
Select the mode 1-24 single (the green LED lights up) via the MODE SELECT button. In this mode, you can use
all 24 channels.
3)
Push the MASTER slider controls A and B to their maximum positions. Note: Control A completely up and control
B completely down.
4)
Set the required light position via the slider controls 1 to 24.
5)
Press the RECORD/SHIFT button once to store this position in the RAM.
6)
Repeat steps 4 and 5 with different positions of the slider controls in order to get an optimal light effect. You can
store up to 99 steps per memory.
7)
The programmed steps must now be transferred from the RAM to the ROM. Proceed as follows: Select a memory
page (1 to 4) via the PAGE/REC CLEAR button. Hold the RECORD/SHIFT button down and press one of the
flash buttons 1 to 13 in section PRESET B. You can store up to 99 steps per memory. There are in total 4 pages
with 12 memories each.
8)
Exit the programming mode (press RECORD/SHIFT and REC EXIT buttons). The red programming LED must go
off.
EXAMPLE: PROGRAMMING A LINEAR RUNNING LIGHT EFFECT
1)
Switch the programming mode on (press RECORD/SHIFT and buttons 1, 5, 6 and 8).
2)
Set both MASTER slider controls to the maximum (A upwards, B downwards).
3)
Select mode 1-24 single via the MODE SELECT button (the green LED lights up).
4)
Push the control 1 to 10 (maximum) and press the RECORD/SHIFT button once.
5)
Push the controls 1 to zero and 2 to maximum and press RECORD/SHIFT again
6)
Push controls 2 to zero and 3 to maximum and press RECORD/SHIFT again.
7)
Repeat these steps up to control 24.
8)
Select a memory page (1 to 4) via the PAGE/REC CLEAR button.
9)
Save the running light effect in this page by pressing one of the flash buttons in section PRESET B (1 to 12). Use
e.g. button number 1.
10) Leave the programming mode by pressing simultaneously the RECORD/SHIFT and REC EXIT buttons.
PLAYING A RUNNING LIGHT PATTERN
1)
Select the mode CHASE/SCENES via the MODE SELECT button. The red LED lights up.
2)
Push the control of the appropriate channel (memory) from section PRESET B to the top. In our example it was
flash button 1. This triggers the steps which are stored in that memory. If the appropriate slider control was
already in the upper position, it is necessary to pull it down first and push it up again to trigger the pattern.
ERASING A RUNNING LIGHT PATTERN
1)
Activate the programming mode (press RECORD/SHIFT and buttons 1, 5, 6 and 8 –the top row).
2)
Select the required page (1 to 4) via the PAGE/REC CLEAR button.
3)
Hold the RECORD/SHIFT button down and press quickly TWICE the appropriate flash button from section
PRESET B in which the pattern to be erased is stored.
4)
Release the RECORD/SHIFT. All indicator LEDs light up to confirm.
CHANGING A RUNNING LIGHT PATTERN
A running light pattern (scene) can contain up to 99 steps. These steps can be changed or erased later. You can also
add steps later. Each 'step' is a determined setting of the variable light intensity (0-100%) of 24 lamps or groups of
lamps.
Erasing a particular step:
1) Activate the programming mode (press RECORD/SHIFT and simultaneously 1, 5, 6, and 8).
2) Select the required page via the PAGE button.
3) Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
5)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light
pattern (flash buttons in the lower row of the section PRESET B).
6)
Release the EDIT button and select via the STEP button the step to be erased.
7)
Press the DELETE button and the selected step will be erased from the memory.
8)
Leave the programming mode by holding the RECORD/SHIFT button down while pressing twice the REC/EXIT
button.
Adding steps:
1)
Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2)
Select the required page via the PAGE button.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern
(flash buttons in the lower row of the section PRESET B).
5)
Release the EDIT button and select via the STEP button the step just after the step to be added.
6)
Set the required light position via the slider controls, press the RECORD/SHIFT button and then the INSERT
button.
7)
If required, repeat steps 5 and 6 to add more steps.
8)
Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
User manual DISCOVERY 12/24 Triton Blue | Rev. Sep 2013 | www.triton-‐blue.com
Publicidad
