Installation Instructions; Product Care - Perry Electric 1DCACPH13 Instrucciones De Uso

00060723 int_nov2017_Layout 1 20/11/2017 12:53 Pagina 5
• Allow your appliance to cool before storing away and do not wrap the supply
cord around the hairdryer in storage.
• The A-weighted sound pressure level of the hairdryers for commercial use is
below 70 dB(A).

INSTALLATION INSTRUCTIONS

Installation of wall holder
This wall holder must only be installed by a qualified electrician
in conformity to applicable safety standards.
The wall holder may be installed in one of two ways:
A = for fixed connection lead
B = for mobile connection lead
Attention: before installing the wall holder always switch off
the general switch of your mains electricity.
For each pole a switch with a minimum break distance between
contacts of 3 mm must be fitted up-line of the appliance.
Each time the appliance is opened, the switch must be used to
disconnect the appliance.
The connection wiring must be type H05VV-F 2x1,5 mm
Method A
IMPORTANT: Refer to the figures for the model you have
purchased.
1. Unscrew the screw (1) (fig. 1) and remove the cover from the
wall unit.
2. Break the plastic membrane (3) at the back of the wall unit
(fig. 3A).
3. Route the main power cable from the wall (4) through the
hole left by the plastic membrane (3) (fig. 3A).
4. Fix the back of the wall unit to the wall using the fixing screws
and wall plugs provided (fig. 2).
5. Remove the terminal strip (5). The input power cable (4) and
the output power cable (9) of hairdryer with max input current
of 10A,if not already connected, must be connected to the
terminal strip(5).
6. Reposition the terminal strip. Tighten the cable clamp
(6 and 10) with its own screws. (fig. 3A). IMPORTANT: This
appliance is double insulated and has no ground (earth)
connection.
7. Fit the cover back on the wall unit with (1) (fig. 1).
8. Switch the power on at the mains switch. The hair dryer is
now ready to use.
Method B
IMPORTANT: Refer to the figures for the model you have
purchased.
1. Unscrew the screw (1) (fig. 1) and remove the cover from the
wall unit.
2. Break the plastic membrane (7) (fig. 3B).
3. Fix the back of the wall unit to the wall using the fixing screws
and wall plugs provided (fig. 2).
4. Route the input power cable (8) and the output power (9)
into the holes (fig. 3B).
5. Remove the terminal strip (5). The input power cable (8) and
the output power cable (9) of hairdryer with max input current
of 10A,if not already connected, must be connected to the
terminal strip(5).
In mod. 036 the Neutral output cable(9) must be connected
to terminal strip (5) and the Line output cable (9) to terminal
strip (11).
Reposition the terminal strip. Tighten the cable clamp (6 and
10) with its own screws. (fig. 3B). IMPORTANT: This appliance
is double insulated and has no ground (earth) connection.
6. Fit the cover back on the wall unit with (1) (fig. 1).
7. Switch the power on at the mains switch. The hair dryer is
now ready to use.
INSTRUCTIONS FOR USE
Hairdryer with wall holder
Control Switches
Control switch on wall holder
(only for models equipped with a switch) rif. 2 fig. 1:
0-1 = Off/On
2 .
Hairdryer
Pushbutton=On/Off
(pressure must be maintained to operate the hairdryer)

PRODUCT CARE

When not in use, the mains switch on the wall holder should be
in the "Off" position. The hairdryer requires no special care or
attention.
You can clean your appliance with a cloth dampened with water.
The cleaning of hairdryers with detergents, solvents, alcohol
and other chemical products is strictly prohibited.
When necessary, the air inlet grill should be cleaned with a soft
brush or by vacuum cleaner.
Important
This hairdryer conforms to the safety regulations regarding
electrical appliances. This hairdryer has a safety cut-out which
will operate in case of overheating. The dryer will re-set itself
after being left to cool for a few minutes, but please check air
inlet and outlet grills are clear before continuing to use the dryer.
This appliance conforms to European Directives 2014/30/EU,
2014/35/EU, 2011/65/EC, 2009/125/EC and Regulation (EC)
No. 1275/2008.
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point
for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your
local city office, your household waste disposal service or the
shop where you purchased the product.
5