Safety Rules - RODCRAFT RC5900 Instrucciones De Manejo/Instrucciones De Seguridad

Modell Length
RC5900 228mm
RC5905 228mm
RC5910 228mm
RC5920 530mm
RC5930 326mm
RC5940 228mm
• Always wear eye protection and protective clothing / equipment to avoid injuries
• Pay attention, that the operation pressure never exceeds over 6,3 bar
• Do not use pneumatic tools in explosive atmosphere
• For suffi cient tool performance make sure that the correct hose - size and fi ttings are used when connecting the tool
• Disconnect the tool from the air - supply before changing accessories or when not in use
• Never carry the tool by the hose
• Do not touch moving parts
• Keep tool away from your body while working
• Always wear ear – protection
• check air hose connections
• only disconnect the machine without pressure of the air, to avoid infractions by uncontrollable movement of the air hose
Air supply and connections
• Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.
• Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may burst, possibly causing injury.
• The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fi tting is used, the tool can remain charged with air after
disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury.
• Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.
Always disconnect air supply:
1. Before making adjustments;
2. When servicing the tool;
3. When clearing a jam;
4. When tool is not in use;
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
Loading tool
1. When loading tool:
2. Never place a hand or any part of body in fastener discharge area of tool;
3. Never point tool at anyone;
4. Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.
Operation
• Always handle the tool with care:
1. Never engage in horseplay;
2. Never pull the trigger unless nose is directed toward the work;
3. Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.
• The operator must not hold the trigger pulled on contact arm tools except during fastening operation as serious injury could result if the trip accidentally
contacted someone or something, causing the tool to cycle.
• Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted
second fastener may be driven possibly causing injury.
• Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may
result. Do not interfere with the proper operation of the contact arm mechanism.
• Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause defl ection of fasteners which could cause
injury.
• Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be defl ected possibly causing injury.
ONLY TO USE THE MACHINE FOR THE DESCRIBED APPLICATION. RODCRAFT DEBARS LIABILITY FOR CONSEQUENCES FOR ALIENA-
TED APPLICATIONS OR CONTRAVENTION AGAINST THE SAFETY RULES.
You can minimise tool „ down time „ by trying your own trouble shooting before sending a not full functioning tool to our Customer Service
Headquarters or a distributor for expert attention:
• Check all compressor components and air delivery lines for leaks.
• Check airline whether there is dirt, water or rust in the lines
• Check whether the impact mechanism or the air motor is overoiled
• Check whether the compressor and the pressure is as required by the tool.
Tecnical specifi cations
Height Weight
145mm 0.8kg
220mm 0.9kg
243mm 1.16kg
370 mm 3.8kg
349mm 3.45kg
243mm 1.13kg
Trouble shooting
RODCRAFT PNEUMATIC TOOLS GmbH & Co.KG
GBR
Pressure range
4-6,3bar
4-6,3bar
4-6,3bar
5-6,3bar
5-6,3bar
4.5-6,3 bar

Safety rules

Staples/Nails
21-Gauge 6~16mm
21-Gauge 6~16mm
18-Gauget 15~50mm
50 ~ 90mm, 2.9 ~ 3.3mm
45~90mm, 2.5~3.8mm
18-Gauge, 16-40mm, 18-gauge, 16-38mm
13/30