Protecting The Environment - Stanley STHR202 Manual De Instrucciones

16 • ENGLISH
Overload coupling device
If the drill bit his caught or hooked, the driving force
transmitted to the drill shaft will be cut off. This would
generate a strong recoil, so it would be necessary to hold
the tool tightly with both hands to remain in a stable position.
Setting the drilling depth (Fig. E)
The depth stop is a convenient feature to ensure
uniformity in drilling depth. Loosen the side handle to
adjust the depth gauge according to the required depth.
After that, tighten the side handle.
f Slacken the side handle (5) by turning the grip
counter clockwise.
f Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f Tighten the side handle by turning the grip clockwise.
Switching on and off
Warning! Before plugging in to the power source, make
sure the switch can be flipped freely, and can return to its
original position once released.
f To switch the tool on, press the variable speed switch
(1). The tool speed depends on how far you press the
switch.
f As a general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f For continuous operation, press the lock-on button
(2) and release the variable speed switch.
f To switch the tool off, release the variable speed
switch. To switch the tool off when in continuous
operation, press the variable speed switch once
more and release it.
MAINTENANCE
Your STANLEY corded/cordless appliance/tool has
been designed to operate over a long period of time with
a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance on
corded/ cordless power tools:
f Switch off and unplug the appliance/tool.
f Or switch off and remove the battery from the
appliance/ tool if the appliance/tool has a separate
battery pack.
f Or run the battery down completely if it is integral and
then switch off.
f Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
f Regularly clean the ventilation slots in your appliance/
tool/charger using a soft brush or dry cloth.
f Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based
cleaner.
f Regularly open the chuck and tap it to remove any
dust from the interior (when fitted).
Replace the carbon brush (Fig. D)
Lubrication
f Regularly replace and inspect the carbon brush. Once
completely worn out by continuous wear and tear, it
will have to be replaced. Must keep carbon brush
clean and sliding freely within the brush holder. Both
carbon brushes have to be replaced at the same time.
f Remove the fixed screws (9) on the carbon brush to
remove the carbon brush (10) and brush holder.
f Remove the coil spring supporting the carbon brush
(11) in the brush holder, and insert a new carbon
brush that meets the specifications.
f Set up the brush holder again and return the
supporting coil s pring to its original position.
CLEANING
Warning! Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
Warning! Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the material of the parts. Use only
mild soap and damp cloth to clean the tool. Never let any
liquid get inside the tool; never immerse any part of the
tool into liquid.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.