PNI CT36 Manual De Usuario página 11

FIRST USE WARNINGS AND INSTRUCTIONS
1. The system comes with main unit and receiver paired from factory. Before use, you only need to
pair the receiver unit with the nearby Wireless Router.
2. At first start, the thermostat / receiver unit signals by LED 1 = " slow blinks" that means it is
necessary to connect unit to the wireless router with Internet access.
3. Insert 2 AAA alkaline batteries (not included) into the main unit and turn it on by pressing the
ON / OFF button. The settings appear as shown in above description.
4. Connect the receiver unit to a 230 VAC power supply (only qualified personnel). Make sure it
works properly by testing / checking the LED status and turning unit On/Off by dedicated button.
I. PAIRING THERMOSTAT WITH MOBILE APP AND WIRELESS INTERNET ROUTER
1. Connect your smartphone to the 2.4 Ghz wireless Internet router nearby. Activate GPS Location on your
smartphone. For a quick setup make sure both phone, thermostat receiver and wireless router are as close
as possible (1-3 m).
WARNING: Check and make sure that you have a 2.4 Ghz Wireless network available and that you have
connected the phone to it. The new generation routers and phones are also equipped with the 5 Ghz
wireless network activated and the devices connect automatically on this frequency. The thermostat cannot
be connected to the 5 Ghz wireless network because it only works on the 2.4 Ghz wireless frequency. To
configure the router and the 2.4 Ghz wireless network, call a specialist.
1. Download "TuyaSmart" app from Google Play or App Store, andd install and register a new account: Press
the "Sign Up" button and follow on-screen instructions.
2. Add device by pressing the + button in the top right corner.
3. Press "All Devices" and access the Small Home Appliances category.
4. Find "Thermostat" or "Heater" from list and select. Follow the on-screen steps, check the name of the
Wifi network and enter the password of the Wifi network with internet access to which the phone is also
connected. If the wireless network does not appear automatically, check if you have GPS Location enabled,
and if you have your phone connected to a 2.4 Ghz wireless network. Restart procedure.
5. Long press the pairing button on the receiver to enter Wifi pairing mode until LED 1 blinks quickly. (before
this, LED 1 blinks slow, sign that thermostat is not paired with wifi internet router)
6. Tap the "Confirm indicator flash blink" on your phone.
7. Wait a few moments until pairing is complete. The LED 1 on the receiver will stop blinking and turn off. At
this point, connection to the Internet via Wirelessrouter is successful, and the Thermostat icon will appear in
Smartphone app.
If the LED continues to blink slowly, the connection failed, try again from step 1.
FIRST USAGE OF THERMOSTAT
1. With main unit screen ON, change the temperature higher or smaller then measured temperature on
screen.
2. In a maximum 90 seconds, the main unit sends a command to receiver unit, which confirms by turning on /
off LED 1, and by a "click", that is heard from inside relay.
3. From TuyaSmart app (make sure the device appears online after configuring internetpairing ) tap on the
device to access it. Using the "+" and "-" buttons, change the temperature bigger or smaller then measured
temperature from screen.
4. In 90 seconds maximum the app sends command through internet to thermostat receiver unit, which
confirms by turning on / off LED 1, and with a "click" sound inside relay. The temperature will change on the
main unit screen.
If there is no change after 90 - 180 seconds (2 minutes), check again if you have changed the temperature
to bigger / smaller than current temperature displayed and check if the device is online.
II. PAIR MAIN UNIT WITH RECEIVER UNIT
Perform this procedure only if absolutely necessary and find that: if after 10 minutes of successful pairing
with the wireless router, the device appears Offline in the application / the
screen / LED 1 on the receiver is off and the units do not communicate with each other.
11
signal icon is missing from the
EN