FALMEC Brio EASY Manual De Instrucciones página 22

Operating
EN
In the Brio, the air passes through the dust filter and activated
carbon filter and then through the ioniser which acts against
the pollutants present in the home, ionising and purifying the
air that is fed back into the environment.
OPERATION
SET-UP
Once connected to the mains, the appliance is on stand by.
Within 30 seconds you need to press a key in the radio control to assi-
gn it to the BRIO.
Pressing one of the keys 1 - 2 -3 -AUTO, BRIO starts the set-up cycle to
measure the internal and external environmental conditions.
The cycle lasts about 4 minutes and in this phase, keys 1, 2 3, auto of
the keypad are flashing and all functions are disabled.
The key remains active.
1 3
2 Eco OUT
IN
The SET-UP cycle is repeated every 3 hours, or the next time that the
fan is activated.
The SET-UP cycle is not displayed on the radio control.
The SET-UP cycle is disabled when BRIO is OFF.
GENERATING A NEW RADIO CONTROL CODE
1
Auto
2
OUT
3
IN
Eco
RESETTING THE RADIO CONTROL FACTORY-SET CODE
• Switch the power supply to the BRIO off before starting the procedure.
• Press keys and
1 2 3 1 2 3
Eco IN OUT Auto
the reset is confirmed by the display flashing briefly 3 times.
• Reconnect the BRIO to the mains.
• Press any key of the radio control within 30 seconds to assign it to the
BRIO.
and maintenance instructions
Auto
The procedure must be carried
out on the radio control
• Switch the power supply to the BRIO
off before starting the procedure.
1 3
• Press the 1 3 2 and Eco
2 Eco
IN
same time until the display starts fla-
shing.
• Press the key on the radio con-
1 3
2 Eco
IN
trol:
the storage of the new code is confir-
med by the display flashing briefly 3
times. The new code cancels and re-
places the previous, factory-set, code.
• Reconnect the BRIO to the mains.
• Press any key of the radio control
within 30 seconds to assign it to the
BRIO.
on the radio control longer than 5 seconds:
Eco IN OUT Auto
DESCRIPTION OF THE FUNCTIONS
Key Keypad
1 Short pulse:
set speed 1 to ECO mode.
Long pulse: Brio ON/OFF
Short pulse:
2
set speed 2 to ECO mode.
Short pulse:
3
set speed 3 to ECO mode.
Active the automatic air
cleaning cycle: the speed
Auto
is decided by BRIO accor-
ding to the quality of the
air on the room.
Eco
IN
OUT
Short pulse:
Light ON/OFF.
1 2 3
Eco
Long pulse: Light intensity
increase / decrease
AIR QUALITY
keys at the OUT Auto
OUT IN Auto
OUT Auto
The more pollutants present, the more intense the colour yellow.
WHICH SPEED IS TO BE SELECTED?
- 1st speed: keeps the air clean with low noise
(green leaves).
- 2nd speed: normal conditions of use.
(moderately yellow leaves).
- 3rd speed: high presence of pollutants
(yellow leaves).
LIGHTING
Brio is equipped with high-efficiency, low-consumption LEDs, very long
life and "dimmer" function (see OPERATION).
MAINTENANCE
Before carrying out any cleaning or maintenance opera-
tions, disconnect from the power supply.
Do not use detergents containing abrasive, acidic or cor-
rosive substances or abrasive cloths.
Regular maintenance guarantees proper operation and performance
over time.
Special attention is paid to the metallic grease filter and the ceramic el-
ement: their frequent cleaning reduces the build-up of dust and other
substances.
22
Radio control
Set speed 1 to the selected mode
(ECO, IN, OUT)
Set speed 2 to the selected mode
(ECO, IN, OUT)
Set speed 3 to the selected mode
(ECO, IN, OUT)
Active the automatic air cleaning
cycle: the speed is decided by BRIO
according to the quality of the air on
the room.
Activate the air renewal cycle.
The duration of the air IN/OUT cycles
depends on the internal and external
temperature, and is set to maximise
the efficiency of the thermal exchan-
ger.
The fan speed may be adjusted to the
three available levels.
Activate the continuous expulsion of
ambient air.
The fan speed may be adjusted to the
three available levels.
Activate the continuous expulsion of
ambient air.
The fan speed may be adjusted to the
three available levels.
Short pulse:
Light ON/OFF.
OUT Auto
IN
Long pulse:
Light intensity increase / decrease
The air quality is displayed by the colour of the leave.
Green = optimum quality.
Yellow = presence of pollutants.
Brio