RAVAK SABINA BASE Instrucciones De Montaje página 3

GB
Instructions for installing -
1. . Set the shower tray bottom-up on a soft mat. On the metal girders (on the ends with two 12,5 mm dia.openings),
fit the M 12x125 thread rods ended with plastic legs.Fit the other side of one of the girders with 330 mm long thread
rod that has the plastic legs on both ends. Fit the remaining girder with the M 12 x 125 thread rod. Set the metal
girders on reinforced bottom of the shower tray, so that the long thread rod supports the tray seat, and so that the
girder ends are close together and open toward the the edge of the tray. Move the girders as shown at the pictire, so
that the 12,5 mm openings are 500 mm from each other and 50-80 mm from the edgeof the tray -while still being
symmetric with the diagonal axis of the shower tray.
2. On the tray bottom, mark the outlines of the girders and location of the 6 mm mounting openings. Set the girders
aside, use the 3 mm drill bit to drill the 10 mm deep fixing openings. ATTENTION: Drill only in the reinforced tray
bottom using the buffer so as not to drill through the plastic bottom of the shower tray. Apply a layer of sanitary
silicon along the horizontal edges of the girders to level the tray bottom, and use the 5,5 x 16 mm screws to mount
the girders. Likewise, apply a small amount of the sanitary silicon under the plastic leg that supports the seat of the
tray. Use adequate force to tighten screws in the supportive leg under the seat and secure them with nuts.
3. Following the separate instruction sheet, fit the tray with the waste siphon complex. Set the tray into its chosen
place in appropriate height. Use a spirit level to make sure that the tray is horizontal -if necessary, level is by twisting
the supportive legs into appropriate height. Tighten the contra-nuts. Mark the opuitlines of the tray upper edges on
the walls. Following the main instruction sheet, attach the mounting clips on the waals and fit the tray with the waste
siphon complex. When casing the tray, leave out an opening for the siphon and cover it (e.g. with a tile). Before yoiu
finally set the tray, apply some sanitary silicon into the shorter claws of all the clips, and hang the tray on them.
Horizontal tiling of the tray should reach up to 2-3 mm beneath the tray upper edge. Fill this 2-3 mm gap with the
sanitary silicon.
MOUNTING KIT
1. Metal Girder 750 mm long
2. Thread Rod M 12 x 125 mm
3. Thread Rod M 12 x 330 mm
4. Plastic leg M 12x40 mm
5. Nut M 12
6. Screw dia.5,5 x 16 mm
7. Drill Bit 3 mm dia
MAINTENANCE AND CLEANING - Do not overlook!
Maintain the product only by wiping its painted, glass or plastic pieces with a soft cloth. Use the detergents recommended by the
manufacturer. Never use any abrasive pastes, dissolvents, acetone or detergents and desinfectants, that contain chlorine
manufacturer is not liable for damage caused by wrong or careless use of cleaning materials.
The manufacturer recommends the use of the following Ravak products:
perfect maintenance of the protective Anticalc glass layer. This layer is factory applied to all safety glass panels. Easy application-
perfect results. RAVAK DISINFECTANT -
household, also recommended for maintenance of bathtub hydromassage systems.
detergent has a pleasant fragrance. The product complements the series of specialized chemicals by RAVAK.
The manufacturer is not liable for damage caused by incorrect installation, use or maintenance. For further information,
contact your local Ravak dealer.
The manufacturer reserves the right to amend or improve on existing designs or features.
Please help preserve the environment by observing local country guidelines or laws regarding re-cycling. Materials which are not
suitable for re-cycling must be disposed of at an official and suitable waste control centre.
SABINA 90
13 pcs
A solution with significant disinfecting effects-intended for versatile use in every
the BASE supports for SABINA, SABIUS shower trays
2 pcs 1.
3 pcs 2. Thread Rod M 12 x 125 mm
1 pcs 3. Thread Rod M 12 x 330 mm
5 pcs 4. Plastic leg M 12x40 mm
5. Nut M 12
8 pcs 6. Screw dia.5,5 x 16 mm
1 pc 7. Drill Bit 3 mm dia
RAVAK ANTICALC CONDITIONER -
MOUNTING KIT
SABINA 80
Metal Girder 650 mm long
RAVAK CLEANER -
2 pcs
3 pcs
1 pcs
5 pcs
13 pcs
8 pcs
1 pc
. The
To be used for
This high efficiency